Disclaimer
How to change front anti roll bar links on Toyota Aygo AB1 – replacement guide
downloads:
20
Views:
414
Important!
This replacement procedure can be used for:
TOYOTA AYGO (WNB1_, KGB1_) 1.0 GPL (KGB10_), TOYOTA AYGO (WNB1_, KGB1_) 1.4 D-4D (WNB10_) … View more
The steps may slightly vary depending on the car design.
TOYOTA AYGO (WNB1_, KGB1_) 1.0 GPL (KGB10_), TOYOTA AYGO (WNB1_, KGB1_) 1.4 D-4D (WNB10_) … View more
The steps may slightly vary depending on the car design.
How to change front anti roll bar link / front drop link on TOYOTA AYGO 1 (AB10) [TUTORIAL AUTODOC]
All the parts you need to replace – Anti Roll Bar Links for AYGO (WNB1_, KGB1_) and other TOYOTA models
Anti-roll bar link
Alternative products
Anti-roll bar link
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #12
Impact socket №12
Wheel impact socket #19
Ratchet wrench
Torque wrench
Hydraulic transmission jack
Crow bar
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on Toyota Aygo AB1 in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- All work should be done with the engine stopped.
Replacement: anti roll bar links – Toyota Aygo AB1. Take the following steps:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3
Raise the front of the car and secure on supports. - Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Toyota Aygo AB1 - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #12. - Step 8
Unscrew the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #12. Use a drive socket #12. Use a ratchet wrench. - Step 9
Remove the stabilizer rod. Use a crowbar.Replacement: anti roll bar links – Toyota Aygo AB1. Professionals recommend:Examine stabiliser bushes. Replace them if needed. - Step 10Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.Step 11
Install a new rod, tighten the fasteners. - Step 12
Support the arm. Use a hydraulic transmission jack. - Step 13
Tighten the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #12. Use a drive socket #12. Use a torque wrench. Tighten it to 18 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 1
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the TOYOTA Aygo (AB10) model.
Popular maintenance tutorials for Toyota Aygo AB10
Free download PDF
2.75 MB
Free download PDF2.31 MB
Free download PDF2.47 MB
Free download PDF2.77 MB
Free download PDF2.36 MB
Free download PDF2.11 MB
Complete guides for changing the Drop links on different TOYOTA AYGO models
Free download PDF2.12 MB
Free download PDF972.8 KB
Free download PDF1.61 MB
Free download PDF1.68 MB
Free download PDF1.73 MB
Free download PDF1.32 MB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your TOYOTA AYGO (WNB1_, KGB1_)
View more
How to remove rust | AUTODOC tips
How to Prevent Premature Wear on Your Car Boot Damper | AUTODOC
Revive Your Tyres: Expert Tips for a Lasting Shine | AUTODOC Guide
Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips
