Important!

This replacement procedure can be used for:
TOYOTA LAND CRUISER (KDJ12_, GRJ12_) 4.0 (GRJ120), TOYOTA LAND CRUISER (KDJ12_, GRJ12_) 3.0 D (LJ120, LJ125), TOYOTA LAND CRUISER (KDJ12_, GRJ12_) 4.0 (GRJ120, GRJ125, GRJ121), TOYOTA LAND CRUISER (KDJ12_, GRJ12_) 3.0 D-4D (KDJ120, KDJ125), TOYOTA LAND CRUISER (KDJ12_, GRJ12_) 3.0 D-4D (KDJ120), TOYOTA LAND CRUISER (KDJ12_, GRJ12_) 4.0 (GRJ120), TOYOTA LAND CRUISER (KDJ12_, GRJ12_) 3.0 D (KZJ120), TOYOTA LAND CRUISER (KDJ12_, GRJ12_) 4.0 V6 VVT-i (GRJ125) … View more

The steps may slightly vary depending on the car design.

How to change rear anti roll bar link on TOYOTA LAND CRUISER PRADO 3 (J120) [AUTODOC]

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – Toyota Prado J120. Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Copper grease 
                    
                      Combination spanner #12
                    
                      Combination spanner #14
                    
                      Combination spanner #17
                    
                      HEX bit No.H6
                    
                      Wheel impact socket #21
                    
                      Torque wrench
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on Toyota Prado J120 in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
All work should be done with the engine stopped.

Replacement: anti roll bar links – Toyota Prado J120. Take the following steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 3

Raise the rear of the car and secure on supports.
Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. Toyota Prado J120
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Support the rear suspension beam. Use a hydraulic transmission jack.
Step 8

Unscrew the fasteners connecting the stabilizer link to the rear suspension beam. Use a combination spanner #12. Use a combination spanner #14.
Step 9

Unscrew the fasteners connecting the stabiliser link to the stabiliser bar. Use a combination spanner #17. Use HEX No.H6.
Step 10

Remove the stabilizer rod.
Step 11

Detach the stabilizer link from the rear suspension beam.

Replacement: anti roll bar links – Toyota Prado J120. Tip:
Examine stabiliser bushes. Replace them if needed.
Step 12

Treat all joints of the stabiliser link. Use copper grease.
Step 13

Install a new rod, tighten the fasteners.
Step 14

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use HEX No.H6. Use a torque wrench. Tighten it to 65 Nm torque.
Step 15

Attach the stabilizer link to the rear suspension beam.
Step 16

Screw in the fasteners connecting the stabilizer link to the rear suspension beam. Use a combination spanner #12. Use a combination spanner #14.
Step 17

Remove the mounting from under the rear axle beam.

Replacement: anti roll bar links – Toyota Prado J120. AUTODOC recommends:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 18

Treat all joints of the stabiliser link. Use copper grease.
Step 19

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 20

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Toyota Prado J120
Step 21

Screw in the wheel bolts. Use wheel impact socket #21.
Step 22

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 112 Nm torque.
Step 23

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Land Cruiser Prado 120 (J120) model

Prado 120 tyre size

How to change front upper arm on Toyota Prado J120 – replacement guide

Free download PDF
2.74 MB
How to change rear suspension lower trailing arm on Toyota Prado J120 – replacement guide

Free download PDF
1.69 MB
How to change track rod end on Toyota Prado J120 – replacement guide

Free download PDF
1.75 MB
How to change front anti roll bar links on Toyota Prado J120 – replacement guide

Free download PDF
1.73 MB
How to change front brake pads on Toyota Prado J120 – replacement guide

Free download PDF
2.08 MB
How to change rear brake pads on Toyota Prado J120 – replacement guide

Free download PDF
1.93 MB

How to change front anti roll bar links on Toyota Prado J120 – replacement guide

Free download PDF
1.73 MB
How to change front anti roll bar links on TOYOTA LAND CRUISER 150 (KDJ15_, GRJ15_) – replacement guide

Free download PDF
1.66 MB
How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on Toyota Yaris P1 – replacement guide

Free download PDF
1.61 MB
How to change front anti roll bar links on Toyota Aygo AB1 – replacement guide

Free download PDF
2.05 MB
How to change front anti roll bar links on Toyota Auris E15 – replacement guide

Free download PDF
1.22 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

The Ultimate Guide to Engine Bay Cleaning | AUTODOC

6K views

Published on: 11/09/2020
TOP 6 WD-40 lifehacks | AUTODOC tips

13K views

Published on: 15/07/2021
What to do if the ABS light comes on: DIY Diagnostics Tips

8K views

Published on: 11/03/2021
DIY starter repair | AUTODOC tips

158K views

Published on: 31/08/2023