Important!

This replacement procedure can be used for:
TOYOTA Yaris Hatchback (_P1_) 1.0 (SCP10_), TOYOTA Yaris Hatchback (_P1_) 1.5 (NCP13_), TOYOTA Yaris Hatchback (_P1_) 1.4 D-4D (NLP10_), TOYOTA Yaris Hatchback (_P1_) 1.3 (SCP12_, SCP13_), TOYOTA Yaris Hatchback (_P1_) 1.0 (SCP10_), TOYOTA Yaris Hatchback (_P1_) 1.5 (NCP13_), TOYOTA Yaris Hatchback (_P1_) 1.5 (NCP13_) … View more

The steps may slightly vary depending on the car design.

How to change front anti roll bar link on TOYOTA YARIS XP10 TUTORIAL | AUTODOC

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – Toyota Yaris P1. Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Combination spanner #13
                    
                      Drive socket # 13 
                    
                      Wheel impact socket #21
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Ball joint puller
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: anti roll bar links – Toyota Yaris P1. AUTODOC recommends:

Replace the stabiliser links on Toyota Yaris P1 in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
All work should be done with the engine stopped.

Replacement: anti roll bar links – Toyota Yaris P1. Use the following procedure:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 3

Raise the front of the car and secure on supports.
Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. Toyota Yaris P1
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.

Step 7

Unscrew the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #13. Use a drive socket #13. Use a ratchet wrench.
Step 8

Unscrew the fasteners connecting the stabiliser link to the stabiliser bar. Use a combination spanner #13. Use a drive socket #13. Use a ratchet wrench.
Step 9

Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 10

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #19.
Step 11

Disconnect the ball joint from the steering knuckle. Use a ball joint puller.
Step 12

Remove the stabilizer rod.

Replacement: anti roll bar links – Toyota Yaris P1. AUTODOC experts recommend:
Examine stabiliser bushes. Replace them if needed.
Step 13

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.

Step 14

Install a new rod, tighten the fasteners.
Step 15

Support the arm. Use a hydraulic transmission jack.
Step 16

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #13. Use a drive socket #13. Use a torque wrench. Tighten it to 18 Nm torque.
Step 17.1

Tighten the fastener connecting the stabilizer bar with the control arm.

Step 17.2

Use a combination spanner #13. Use a drive socket #13. Use a torque wrench. Tighten it to 18 Nm torque.
Step 18

Treat all joints of the stabiliser link. Use copper grease.
Step 19

Connect the ball joint to the steering knuckle.
Step 20

Remove the support from under the arm.

AUTODOC recommends:
Replacement: anti roll bar links – Toyota Yaris P1. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 21

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 22

Clean the brake disk surface. Use a brake cleaner.

Replacement: anti roll bar links – Toyota Yaris P1. Professionals recommend:
After applying the spray, wait a few minutes.
Step 23

Install the wheel.

Replacement: anti roll bar links – Toyota Yaris P1. Tip from AUTODOC:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 24

Screw in the wheel bolts. Use wheel impact socket #21.
Step 25

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 103 Nm torque.
Step 26

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Yaris I Hatchback (P1) model

Toyota Yaris Mk1 tyre size

How to change front lower arm on Toyota Yaris P1 – replacement guide

Free download PDF
1.71 MB
How to change front wheel bearing on Toyota Yaris P1 – replacement guide

Free download PDF
2.53 MB
How to change rear wheel bearing on Toyota Yaris P1 – replacement guide

Free download PDF
1.13 MB
How to change front strut mount on Toyota Yaris P1 – replacement guide

Free download PDF
1.94 MB
How to change track rod end on Toyota Yaris P1 – replacement guide

Free download PDF
1.4 MB
How to change front brake pads on Toyota Yaris P1 – replacement guide

Free download PDF
1.58 MB

How to change front anti roll bar links on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.6 MB
How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on Toyota Aygo AB1 – replacement guide

Free download PDF
2.05 MB
How to change rear anti roll bar links on Toyota Prado J120 – replacement guide

Free download PDF
1.68 MB
How to change front anti roll bar links on Toyota Auris E15 – replacement guide

Free download PDF
1.22 MB
How to change rear anti roll bar links on Toyota RAV4 II – replacement guide

Free download PDF
1.32 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

5 mistakes when replacing consumables

6K views

Published on: 06/02/2025
K2 ROTON wheel cleaner overview

4K views

Published on: 27/03/2025
#DIY Wheel Rim Restoration: Revive Scratches and Chips Easily!

7K views

Published on: 18/07/2024
DIY manual gearbox restoration | Drivetrain restoration – Part 3

18K views

Published on: 14/11/2024