Important!

This replacement procedure can be used for:
TOYOTA CELICA (ZZT23_) 1.8 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – TOYOTA CELICA (ZZT23_). Tools you might need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Ceramic grease
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Drive socket # 14
                    
                      Wheel impact socket #19
                    
                      Ratchet wrench
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on TOYOTA CELICA (ZZT23_) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – TOYOTA CELICA (ZZT23_) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3

Raise the car.

Replacement: anti roll bar links – TOYOTA CELICA (ZZT23_). Tip from AUTODOC:
If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. TOYOTA CELICA (ZZT23_)
Step 5

Remove the wheel.
Step 6

Clean the sway bar link fastener. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #14. Use a ratchet wrench.
Step 8

Clean the sway bar link fastener. Use a wire brush. Use WD-40 spray.
Step 9

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #14. Use a ratchet wrench.
Step 10

Remove the stabilizer rod. Use a crowbar.

Replacement: anti roll bar links – TOYOTA CELICA (ZZT23_). AUTODOC experts recommend:
Examine stabiliser bushes. Replace them if needed.
Step 11

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 12

Ιnstall the transverse stabilizer link. Use a crowbar.
Step 13

Screw in the sway bar link fasteners. Use a drive socket #14. Use a ratchet wrench.
Step 14

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #14. Use a torque wrench. Tighten it to 44 Nm torque.
Step 15

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #14. Use a torque wrench. Tighten it to 44 Nm torque.
Step 16

Treat all joints of the stabiliser link. Use copper grease.
Step 17

Clean the wheel rim mounting seat. Use a wire brush.
Step 18

Treat the surface where the brake disc contacts the wheel rim. Use ceramic grease.
Step 19

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – TOYOTA CELICA (ZZT23_). After applying the spray, wait a few minutes.
Step 20

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. TOYOTA CELICA (ZZT23_)
Step 21

Screw in the wheel bolts. Use wheel impact socket #19.
Step 22

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 103 Nm torque.
Step 23

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Celica VII Coupe (T230) model

Toyota Celica T23 tyre size

How to change rear wheel bearing on TOYOTA Celica VII Coupe (T230) – replacement guide

Free download PDF
1.5 MB
How to change front brake pads on TOYOTA Celica VII Coupe (T230) – replacement guide

Free download PDF
1.42 MB
How to change spark plugs on TOYOTA CELICA (ZZT23_) – replacement guide

Free download PDF
1.39 MB
How to change rear windshield wipers on TOYOTA CELICA (ZZT23_) – replacement guide

Free download PDF
532.48 KB
How to change front windshield wipers on TOYOTA Celica VII Coupe (T230) – replacement guide

Free download PDF
1.5 MB
How to change engine oil and filter on TOYOTA Celica VII Coupe (T230) – replacement guide

Free download PDF
2.04 MB

How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on Toyota Yaris P1 – replacement guide

Free download PDF
1.61 MB
How to change front anti roll bar links on Toyota Aygo AB1 – replacement guide

Free download PDF
2.05 MB
How to change rear anti roll bar links on Toyota Prado J120 – replacement guide

Free download PDF
1.68 MB
How to change front anti roll bar links on Toyota Auris E15 – replacement guide

Free download PDF
1.22 MB
How to change rear anti roll bar links on Toyota RAV4 II – replacement guide

Free download PDF
1.32 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Understanding Airbag Light Warnings | Essential Tips for Car Safety

6K views

Published on: 10/04/2023
Top 5 reasons why the suspension knocks | AUTODOC tips

2M views

Published on: 09/09/2022
Easy Steps to Fix Minor Scratches on Your Vehicle | AUTODOC tips

8K views

Published on: 12/05/2022
5 more brake repair mistakes | Stop making these brake repair mistakes

9K views

Published on: 22/01/2025