Disclaimer
How to change hand brake cable on FORD MONDEO III Estate (BWY) – replacement guide
downloads:
3
Views:
26
Recommended replacement interval for the part category Hand brake cable : 40000 km
Important!
This replacement procedure can be used for:
FORD MONDEO III Estate (BWY) 2.0 16V DI / TDDi / TDCi, FORD MONDEO III Estate (BWY) 2.0 TDCi … View more
The steps may slightly vary depending on the car design.
FORD MONDEO III Estate (BWY) 2.0 16V DI / TDDi / TDCi, FORD MONDEO III Estate (BWY) 2.0 TDCi … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Hand brake Cable for MONDEO III Estate (BWY) and other FORD models
WD-40 spray
Brake cleaner
Copper grease
Torque wrench
Drive socket # 10
Drive socket # 16
Wheel impact socket #19
Ratchet wrench
Nippers
Hammer
Round-nose pliers
Crow bar
Hydraulic transmission jack
Wheel chock
Replacement: hand brake cable – FORD MONDEO III Estate (BWY). Tip from AUTODOC:
- Replace the parking brake cables in pairs.
- All work should be done with the engine stopped.
Replacement: hand brake cable – FORD MONDEO III Estate (BWY). Use the following procedure:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3
Raise the rear of the car and secure on supports. - Step 4
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. FORD MONDEO III Estate (BWY) - Step 5
Remove the wheel. - Step 6
Disconnect the parking brake cable from the brake caliper. Use nippers. Use a crowbar. - Step 7
Detach the parking brake cable from the car body. Use a hammer. Use a crowbar. - Step 8
Detach the silencer from the bracket. Use a crowbar. - Step 9
Support the silencer. Use a hydraulic transmission jack. - Step 10
Detach the silencer from the bracket. Use a crowbar. - Step 11
Lower the hydraulic transmission jack by 10-15 cm. - Step 12
Unscrew the exhaust heat shield fasteners. Use a drive socket #10. Use a ratchet wrench. - Step 13
Remove the exhaust heat shield. - Step 14
Clean the fastener of the parking brake cable. Use WD-40 spray. - Step 15
Loosen the parking brake cable. Use a drive socket #16. Use a ratchet wrench. - Step 16
Release the parking brake cable. Use round-nose pliers. - Step 17
Remove the parking brake cable. - Step 18
Install a new parking brake cable. - Step 19Secure the parking brake cable.Step 20
Attach the parking brake cable to the car body.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the FORD Mondeo Mk3 Estate (BWY) model.
Popular maintenance tutorials for Ford Mondeo bwy
Free download PDF
1.76 MB
Free download PDF1.67 MB
Free download PDF1.97 MB
Free download PDF1.94 MB
Free download PDF1.88 MB
Free download PDF1.45 MB
Complete guides for changing the Parking brake cable on different FORD MONDEO models
Free download PDF1.98 MB
Free download PDF1.89 MB
Free download PDF1.51 MB
Free download PDF2.63 MB
Free download PDF2.2 MB
Free download PDF1.5 MB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your FORD MONDEO III Estate (BWY)
View more
What to do if your check engine light is on | AUTODOC tips
How to easily repair a punctured tyre | AUTODOC tips
Why do your brakes squeak? | AUTODOC tips
What to do if the TPMS light is on | AUTODOC tips
