
Disclaimer
How to change front brake caliper on Ford Mondeo BWY – replacement guide
downloads:
2
Views:
67

Recommended replacement interval for the part category Brake caliper : 100000 km
Important!
This replacement procedure can be used for:
FORD MONDEO III Estate (BWY) 2.2 TDCi, FORD MONDEO III Estate (BWY) 1.8 16V, FORD MONDEO III Estate (BWY) 2.0 16V, FORD MONDEO III Estate (BWY) 2.5 V6 24V, FORD MONDEO III Estate (BWY) 2.0 16V DI / TDDi / TDCi, FORD MONDEO III Estate (BWY) 2.0 16V TDDi / TDCi, FORD MONDEO III Estate (BWY) 2.0 TDCi, FORD MONDEO III Estate (BWY) ST220, FORD MONDEO III Estate (BWY) 1.8 SCi, FORD MONDEO III Estate (BWY) 2.2 TDCi, FORD MONDEO III Estate (BWY) 3.0 V6 24V … View more
The steps may slightly vary depending on the car design.
FORD MONDEO III Estate (BWY) 2.2 TDCi, FORD MONDEO III Estate (BWY) 1.8 16V, FORD MONDEO III Estate (BWY) 2.0 16V, FORD MONDEO III Estate (BWY) 2.5 V6 24V, FORD MONDEO III Estate (BWY) 2.0 16V DI / TDDi / TDCi, FORD MONDEO III Estate (BWY) 2.0 16V TDDi / TDCi, FORD MONDEO III Estate (BWY) 2.0 TDCi, FORD MONDEO III Estate (BWY) ST220, FORD MONDEO III Estate (BWY) 1.8 SCi, FORD MONDEO III Estate (BWY) 2.2 TDCi, FORD MONDEO III Estate (BWY) 3.0 V6 24V … View more
The steps may slightly vary depending on the car design.
How to change a front brake caliper on FORD MONDEO 3 TUTORIAL | AUTODOC

All the parts you need to replace – Brake Calipers for MONDEO III Estate (BWY) and other FORD models
Brake caliper
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Flare nut spanner №11
Flare nut spanner №14
Combination spanner #19
Drive socket # 13
Wheel impact socket #19
Ratchet wrench
Torque wrench
Brake hose clip
Flat Screwdriver
Brake bleeder kit
Wheel chock
Replacement: brake caliper – Ford Mondeo BWY. AUTODOC recommends:
- The replacement procedure is identical for the left and right brake calipers on the same axle.
- All work should be done with the engine stopped.
Replacement: brake caliper – Ford Mondeo BWY. Take the following steps:
- Step 1Open the bonnet. Unscrew the brake fluid reservoir cap.
- Step 2Secure the wheels with chocks.
- Step 3Loosen the wheel mounting bolts. Use wheel impact socket #19.
- Step 4Raise the front of the car and secure on supports.Step 5Unscrew the wheel bolts.Replacement: brake caliper – Ford Mondeo BWY. Tip from AUTODOC:To avoid injury, hold up the wheel when unscrewing the bolts.
- Step 6Remove the wheel.
- Step 7Clean the area where the brake hose is connected to the caliper, and the guide pins area. Use a brake cleaner.AUTODOC recommends:Replacement: brake caliper – Ford Mondeo BWY. After applying the spray, wait a few minutes.
- Step 8Clamp the brake hose off using a brake hose clamp.Step 9Loosen the brake hose fastening. Use a flare nut spanner #14.
- Step 10Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
- Step 11Unscrew the brake caliper fastening. Use a combination spanner #19. Use a drive socket #13. Use a ratchet wrench.
- Step 12Remove the guide pins from the brake caliper.
- Step 13Remove the brake caliper. Use a flat screwdriver.Replacement: brake caliper – Ford Mondeo BWY. Professionals recommend:When replacing the brake caliper, it is recommended to check the brake hose for damages and, if necessary, to replace it with a new one.When replacing a brake caliper it is recommended to replace brake pads, check the state of the brake discs and replace them with new ones if necessary.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
- Step 14Unscrew the brake hose from the brake caliper. Use a flare nut spanner #14.Step 15Disconnect the brake hose.
- Step 16Treat the brake hose. Use a brake cleaner.Replacement: brake caliper – Ford Mondeo BWY. Tip from AUTODOC experts:After applying the spray, wait a few minutes.Step 17Install and fix the brake hose into a new caliper.
- Step 18Install the brake caliper and fix it.
- Step 19Screw in the guide pins.
- Step 20.1Tighten the brake caliper fasteners.Step 20.2Use a combination spanner #19. Use a drive socket #13. Use a torque wrench. Tighten it to 30 Nm torque.
- Step 21Tighten the fastener connecting the brake pipe to the brake caliper. Use a flare nut spanner #14. Use a torque wrench. Tighten it to 18 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 1
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the FORD Mondeo Mk3 Estate (BWY) model
Popular maintenance tutorials for Ford Mondeo bwy
Complete guides for changing the Brake calipers on different FORD MONDEO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your FORD MONDEO III Estate (BWY)
View more
- How to Install a New Windscreen Yourself | AUTODOC Expert Tips
- Regain Your Confidence on the Road: Easy Headlight Restoration Tips
- How to fix your car with AUTODOC CLUB
- Coolant comparison test | AUTODOC
Most commonly replaced car parts on FORD MONDEO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME