Important!

This replacement procedure can be used for:
TOYOTA Yaris Verso (_P2_) 1.3 (NCP20_, NCP22_), TOYOTA Yaris Verso (_P2_) 1.5 (NCP21_), TOYOTA Yaris Verso (_P2_) 1.4 D-4D (NLP20_, NLP22_), TOYOTA Yaris Verso (_P2_) 1.3 (NCP20_, NCP22_), TOYOTA Yaris Verso (_P2_) 1.5 (NCP21_) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Strut Mount for Yaris Verso (_P2_) and other TOYOTA models

Top strut mount

        Top strut mount for Yaris Verso (P2) Petrol (86 hp)
      
        Top strut mount for Yaris Verso (P2) Petrol (106 hp)
      
        Top strut mount for Yaris Verso (P2) Diesel (75 hp)
      
        Top strut mount for Yaris Verso (P2) Petrol (84 hp)
      
        Top strut mount for Yaris Verso (P2) Petrol (105 hp)

Replacement: strut mount – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Combination spanner #12
                      
                        Combination spanner #19
                      
                        Drive socket # 14 
                      
                        Drive socket # 17 
                      
                        Drive socket # 19 
                      
                        Wheel impact socket #21
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Flat Screwdriver
                      
                        Hydraulic strut spring compressor
                      
                        Fender cover
                      
                        Wheel chock

Buy tools

Replacement: strut mount – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). AUTODOC recommends:

All mounts of the front shock struts should be replaced simultaneously.
The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
Be sure to replace all self-locking nuts and bolts during installation.
Please note: all work on the car – TOYOTA YARIS VERSO (_NLP2_, _NCP2_) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: strut mount – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Clean the fastener of the bracket that connects the brake hose to the shock strut. Use a wire brush. Use WD-40 spray.

Step 7

Unscrew the brake hose fastening bracket from the shock strut. Use a drive socket #14. Use a ratchet wrench.
Step 8

Remove the bracket from the shock absorber strut.
Step 9

Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 10

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #19. Use a drive socket #19. Use a ratchet wrench.
Step 11

Remove the fastening bolts. Disconnect the steering knuckle from the shock absorber strut.

Step 12

Lower the car. Open the bonnet.

Step 13

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 14

Clean the fasteners of the shock strut upper mount. Use a wire brush. Use WD-40 spray.

Step 15

Unscrew the top fastening of the shock strut mount. Use a combination spanner #12.

Replacement: strut mount – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). AUTODOC recommends:
To avoid injuries, hold the shock strut when undoing the fastening bolts.
Step 16

Remove the suspension strut.
Step 17

Set the shock absorber strut on the spring compressor tool.

Replacement: strut mount – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Tip from AUTODOC experts:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 18

Compress the spring.

Step 19

Remove the protective cap from the shock absorber strut mount. Use a flat screwdriver.
Step 20

Treat the shock strut rod. Use a wire brush. Use WD-40 spray.
Step 21

Remove the strut piston rod nut. Use a drive socket #17. Use a ratchet wrench.
Step 22

Remove the top strut mount. Use a flat screwdriver.
Step 23

Clean the mounting seat of the shock strut mount. Use a wire brush. Use WD-40 spray.

Replacement: strut mount – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Professionals recommend:
Examine the shock absorber dust cap and the bump stop. Replace them if necessary.
Step 24

Install a new strut mount.
Step 25

Tighten the shock strut piston rod nut. Use a drive socket #17. Use a torque wrench. Tighten it to 33 Nm torque.

Replacement: strut mount – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). AUTODOC experts recommend:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 26

Treat the shock strut rod. Use copper grease.
Step 27

Install the protective cap onto the shock absorber strut mount.
Step 28

Decompress the spring.

Step 29

Remove the assembled shock strut.
Step 30

Clean the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 31

Install the shock strut into the wheel arch.

Step 32

Screw the top fastening of the shock strut mount.

AUTODOC recommends:
Important! Hold the suspension strut while screwing in the fastening bolts. TOYOTA YARIS VERSO (_NLP2_, _NCP2_)
Step 33

Tighten the upper fastener of the shock absorber strut mount. Use a combination spanner #12. Use a torque wrench. Tighten it to 35 Nm torque.
Step 34

Treat the fasteners of the shock strut mount. Use copper grease.

Step 35

Remove the fender protection cover. Close the hood.

Step 36

Raise the front of the car and secure on supports.
Step 37

Fix the shock absorber strut on the steering knuckle.

Step 38

Install the fastening bolts.

Step 39

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a combination spanner #19. Use a drive socket #19. Use a torque wrench. Tighten it to 132 Nm torque.
Step 40

Treat the shock strut fasteners. Use copper grease.

Step 41

Install the bracket onto the shock absorber strut.
Step 42

Tighten the brake hose fastening bracket to the shock strut. Use a drive socket #14. Use a ratchet wrench.
Step 43

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 44

Clean the brake disk surface. Use a brake cleaner.

Replacement: strut mount – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 45

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. TOYOTA YARIS VERSO (_NLP2_, _NCP2_)
Step 46

Screw in the wheel bolts. Use wheel impact socket #21.
Step 47

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 103 Nm torque.
Step 48

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Yaris Verso (P2) model.

Browse tyres

How to change front anti roll bar links on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.6 MB
How to change front lower arm on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.62 MB
How to change front wheel bearing on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
2.53 MB
How to change rear wheel bearing on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.13 MB
How to change track rod end on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.34 MB
How to change front brake pads on TOYOTA Yaris Verso (P2) – replacement guide

Free download PDF
1.41 MB

How to change front strut mount on Toyota Yaris P1 – replacement guide

Free download PDF
1.94 MB
How to change strut mount on a car – replacement tutorial

Universal

Free download PDF
1.04 MB
How to change front strut mount on Toyota RAV4 II – replacement guide

Free download PDF
2.43 MB
How to change front strut mount on TOYOTA RAV 4 I (SXA1_) – replacement guide

Free download PDF
2.28 MB
How to change front strut mount on TOYOTA RAV 4 (SXA1_) – replacement guide

Free download PDF
2.27 MB
How to change front strut mount on Honda Jazz GD – replacement guide

Free download PDF
3.1 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

3 things that cause engine damage | AUTODOC tips

9K views

Published on: 07/10/2021
How and why to check your oil | AUTODOC tips

5K views

Published on: 23/02/2023
How to restore a damaged thread | AUTODOC tips

5K views

Published on: 04/05/2023
What causes engine misfire? | AUTODOC

5K views

Published on: 10/07/2020