Important!

This replacement procedure can be used for:
TOYOTA Yaris Verso (_P2_) 1.5 (NCP21_), TOYOTA Yaris Verso (_P2_) 1.3 (NCP20_, NCP22_), TOYOTA Yaris Verso (_P2_) 1.4 D-4D (NLP20_, NLP22_), TOYOTA Yaris Verso (_P2_) 1.5 (NCP21_), TOYOTA Yaris Verso (_P2_) 1.3 (NCP20_, NCP22_) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for Yaris Verso (_P2_) and other TOYOTA models

Alternative products

Wheel bearing kit

Replacement: wheel bearing – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Combination spanner #17
                    
                      Combination spanner #19
                    
                      Drive socket # 17 
                    
                      Drive socket # 19 
                    
                      Drive socket # 30 
                    
                      Wheel impact socket #21
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Tap wrench
                    
                      Hammer
                    
                      Nippers
                    
                      Flat chisel
                    
                      Rubber mallet
                    
                      Bush and bearing driver set
                    
                      Circlip pliers
                    
                      Ball joint puller
                    
                      Wheel chock

Buy tools

Replacement: wheel bearing – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). AUTODOC recommends:

Do not re-use the bearing assembly of your TOYOTA YARIS VERSO (_NLP2_, _NCP2_) car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
All work should be done with the engine stopped.

Replacement: wheel bearing – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Recommended sequence of steps:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: wheel bearing – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Unstake the fastener of the driveshaft. Use a flat metal-working chisel. Use a hammer.
Step 7

Clean the fastener of the driveshaft. Use a wire brush. Use WD-40 spray.

Step 8

Loosen the fastener of the driveshaft. Use a drive socket #30. Use a tap wrench.
Step 9

Remove the drive shaft.

Replacement: wheel bearing – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Tip from AUTODOC:
If necessary, use a rubber mallet.
Step 10

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 11

Unscrew the caliper bracket fastening. Use a drive socket #17. Use a ratchet wrench.
Step 12

Remove the brake caliper together with its bracket.

Replacement: wheel bearing – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). AUTODOC experts recommend:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 13

Remove the brake disc.
Step 14

Remove the cotter pin fixing the tie rod end fastening. Use nippers.
Step 15

Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 16

Unscrew the end fastening nut to the steering knuckle. Use a combination spanner #17.
Step 17

Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
Step 18

Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 19

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #19.
Step 20

Disconnect the ball joint from the steering knuckle. Use a ball joint puller.
Step 21

Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 22

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #19. Use a drive socket #19. Use a ratchet wrench.
Step 23

Remove the fastening bolts.

Step 24

Disconnect the steering knuckle from the shock absorber strut.
Step 25

Remove the steering knuckle together with the hub.
Step 26

Press the wheel hub out from the tapered roller bearing. Use a bush and bearing driver set. Use a hammer.
Step 27

Remove the retaining ring from the steering knuckle. Use circlip pliers.
Step 28

Press out the wheel hub bearing. Use a bush and bearing driver set.
Step 29

Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.

Step 30

Press the new bearing in the steering knuckle. Use a bush and bearing driver set. Use a hammer.

Replacement: wheel bearing – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Tip from AUTODOC experts:
Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
Step 31

Install the retaining ring in the steering knuckle. Use circlip pliers.
Step 32

Press the wheel hub into the bearing inner race. Use a bush and bearing driver set.
Step 33

Install the steering knuckle with a hub in assembly.
Step 34

Install the fastening bolts.

Step 35

Fix the shock absorber strut on the steering knuckle.

Step 36

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a combination spanner #19. Use a drive socket #19. Use a torque wrench. Tighten it to 132 Nm torque.
Step 37

Treat the shock strut fasteners. Use copper grease.
Step 38

Connect the ball joint to the steering knuckle.

Step 39

Tighten the ball joint fastener. Use a combination spanner #19. Use a torque wrench. Tighten it to 98 Nm torque.
Step 40

Clean the splines of the drive shaft CV joint. Use a wire brush. Use WD-40 spray.

Step 41

Mount the drive shaft into the wheel hub.
Step 42

Tighten the drive shaft nut. Use a drive socket #30. Use a tap wrench. Use a torque wrench. Tighten it to 216 Nm torque.
Step 43

Restake the fastener of the driveshaft. Use a flat metal-working chisel. Use a hammer.
Step 44

Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 45

Install the brake disc.
Step 46

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). After applying the spray, wait a few minutes.
Step 47

Install the brake caliper together with its bracket.
Step 48

Tighten the brake caliper bracket. Use a drive socket #17. Use a torque wrench. Tighten it to 88 Nm torque.
Step 49

Connect the tie rod end to the steering knuckle.
Step 50

Tighten the fastening nut connecting the tie rod end to the steering knuckle. Use a combination spanner #17. Use a torque wrench. Tighten it to 49 nm torque.
Step 51

Install the cotter pin. Use nippers.
Step 52

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 53

Clean the brake disk surface. Use a brake cleaner.

Replacement: wheel bearing – TOYOTA YARIS VERSO (_NLP2_, _NCP2_). Professionals recommend:
After applying the spray, wait a few minutes.
Step 54

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. TOYOTA YARIS VERSO (_NLP2_, _NCP2_)
Step 55

Screw in the wheel bolts. Use wheel impact socket #21.
Step 56

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 103 Nm torque.
Step 57

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Yaris Verso (P2) model

Toyota Yaris Verso tyre size

How to change front anti roll bar links on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.6 MB
How to change front lower arm on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.62 MB
How to change rear wheel bearing on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.13 MB
How to change front strut mount on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.85 MB
How to change track rod end on TOYOTA Yaris Verso (_P2_) – replacement guide

Free download PDF
1.34 MB
How to change front brake pads on TOYOTA Yaris Verso (P2) – replacement guide

Free download PDF
1.41 MB

How to change front wheel bearing on Toyota Yaris Mk2 – replacement guide

Free download PDF
3.78 MB
How to change rear wheel bearing on Toyota Yaris Mk2 – replacement guide

Free download PDF
2.64 MB
How to change front wheel bearing on Toyota Yaris P1 – replacement guide

Free download PDF
2.53 MB
How to change rear wheel bearing on Toyota Yaris P1 – replacement guide

Free download PDF
1.13 MB
How to change front wheel bearing on TOYOTA Yaris III Hatchback (XP13) – replacement guide

Free download PDF
3.91 MB
How to change front wheel bearing on TOYOTA Yaris Hatchback (_P13_) – replacement guide

Free download PDF
3.71 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Revive Your Vehicle's Look | How to Restore Wheel Rims Yourself!

6K views

Published on: 13/05/2021
Why Is the Windscreen Washer Not Spraying? Solution

3K views

Published on: 25/04/2025
Engine Overheating? Replace Your Cooling Fan to Fix It

6K views

Published on: 15/11/2020
TOP 5 mistakes when replacing shock absorbers | AUTODOC tips

13K views

Published on: 15/06/2023