Important!

This replacement procedure can be used for:
TOYOTA Wish MPV (_E1_) 2.0 VVTi (ANE10G, ANE11W), TOYOTA Wish MPV (_E1_) 1.8 Hi (ZNE10), TOYOTA Wish MPV (_E1_) 1.8 Hi 4WD (ZNE14G) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – TOYOTA Wish MPV (_E1_). Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Combination spanner #17
                    
                      Combination spanner #19
                    
                      Drive socket # 17 
                    
                      Drive socket # 19 
                    
                      HEX bit no.H6
                    
                      Wheel impact socket #21
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on TOYOTA Wish MPV (_E1_) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
All work should be done with the engine stopped.

Replacement: anti roll bar links – TOYOTA Wish MPV (_E1_). Recommended sequence of steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: anti roll bar links – TOYOTA Wish MPV (_E1_). Tip from AUTODOC experts:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use HEX No.H6. Use a combination spanner #17.
Step 8

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 9

Remove the stabilizer rod. Use a crowbar.

Replacement: anti roll bar links – TOYOTA Wish MPV (_E1_). Tip from AUTODOC experts:
Examine stabiliser bushes. Replace them if needed.
Step 10

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.

Step 11

Install a new rod, tighten the fasteners. Use a combination spanner #19. Use a drive socket #19. Use HEX No.H6. Use a ratchet wrench.
Step 12

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #19. Use a torque wrench. Tighten it to 74 Nm torque.
Step 13

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #19. Use a torque wrench. Tighten it to 74 Nm torque.
Step 14

Treat all joints of the stabiliser link. Use copper grease.
Step 15

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 16

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – TOYOTA Wish MPV (_E1_). After applying the spray, wait a few minutes.
Step 17

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. TOYOTA Wish MPV (_E1_)
Step 18

Screw in the wheel bolts. Use wheel impact socket #21.
Step 19

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 103 nm torque.
Step 20

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the TOYOTA Wish MPV (_E1_) model

TOYOTA Wish MPV (_E1_) tyre size

How to change spark plugs on TOYOTA Wish MPV (_E1_) – replacement guide

Free download PDF
1.68 MB
How to change front windshield wipers on TOYOTA Wish MPV (_E1_) – replacement guide

Free download PDF
1.47 MB
How to change engine oil and filter on TOYOTA Wish MPV (_E1_) – replacement guide

Free download PDF
2.04 MB
How to change engine oil and filter on Toyota Aygo AB1 – replacement guide

Free download PDF
2.32 MB
How to change engine oil and filter on Toyota Auris E15 – replacement guide

Free download PDF
2.23 MB
How to change front brake pads on Toyota Prado J120 – replacement guide

Free download PDF
2.08 MB

How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on Toyota Yaris P1 – replacement guide

Free download PDF
1.61 MB
How to change front anti roll bar links on Toyota Aygo AB1 – replacement guide

Free download PDF
2.05 MB
How to change rear anti roll bar links on Toyota Prado J120 – replacement guide

Free download PDF
1.68 MB
How to change front anti roll bar links on Toyota Auris E15 – replacement guide

Free download PDF
1.22 MB
How to change rear anti roll bar links on Toyota RAV4 II – replacement guide

Free download PDF
1.32 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

5 tools that make car repair incredibly simple | AUTODOC tips

49K views

Published on: 25/01/2024
Fuse Replacement Made Simple: Step-by-Step Guide | AUTODOC

3K views

Published on: 15/08/2020
Why does it burn oil? The main cause of oil consumption in EA888 Gen 1

121K views

Published on: 14/08/2025
How to Use Sandblasting Equipment: Step-by-Step Guide | AUTODOC Tips

5K views

Published on: 16/05/2024