Important!

This replacement procedure can be used for:
FORD MONDEO III Saloon (B4Y) 1.8 16V, FORD MONDEO III Saloon (B4Y) 1.8 16V, FORD MONDEO III Saloon (B4Y) 2.5 V6 24V, FORD MONDEO III Saloon (B4Y) 2.0 16V DI / TDDi / TDCi, FORD MONDEO III Saloon (B4Y) 2.0 16V TDDi / TDCi, FORD MONDEO III Saloon (B4Y) 2.0 TDCi, FORD MONDEO III Saloon (B4Y) ST220, FORD MONDEO III Saloon (B4Y) 1.8 SCi, FORD MONDEO III Saloon (B4Y) 2.2 TDCi, FORD MONDEO III Saloon (B4Y) 3.0 V6 24V, FORD MONDEO III Saloon (B4Y) 2.0 DI … View more

The steps may slightly vary depending on the car design.

How to change front anti roll bar link on FORD MONDEO MK3 Saloon [TUTORIAL AUTODOC]

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – Ford Mondeo Mk3 saloon. Tools you need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #17
                    
                      Drive socket # 17
                    
                      Wheel impact socket #19
                    
                      Ratchet wrench
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on Ford Mondeo Mk3 saloon in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – Ford Mondeo Mk3 saloon – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3

Raise the front of the car and secure on supports.
Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. Ford Mondeo Mk3 saloon
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 8

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 9

Remove the stabiliser link.

Replacement: anti roll bar links – Ford Mondeo Mk3 saloon. Tip from AUTODOC:
Examine stabiliser bushes. Replace them if needed.
Step 10

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 11

Ιnstall the transverse stabilizer link.
Step 12

Tighten the stabiliser link fastener. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 13

Tighten the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #17. Use a torque wrench. Tighten it to 48 Nm torque.
Step 14

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use a drive socket #17. Use a torque wrench. Tighten it to 48 Nm torque.
Step 15

Treat all joints of the stabiliser link. Use copper grease.
Step 16

Clean the wheel rim mounting seat. Use a wire brush.

Step 17

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 18

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – Ford Mondeo Mk3 saloon. After applying the spray, wait a few minutes.
Step 19

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. Ford Mondeo Mk3 saloon
Step 20

Screw in the wheel bolts. Use wheel impact socket #19.
Step 21

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 90 Nm torque.
Step 22

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the FORD Mondeo Mk3 Saloon (B4Y) model

Ford Mondeo mk3 Saloon tyre size

How to change front wheel bearing on Ford Mondeo Mk3 saloon – replacement guide

Free download PDF
3.49 MB
How to change front strut mount on Ford Mondeo Mk3 saloon – replacement guide

Free download PDF
3.79 MB
How to change rear wheel bearing on Ford Mondeo Mk3 saloon – replacement guide

Free download PDF
2.48 MB
How to change rear anti roll bar links on Ford Mondeo Mk3 saloon – replacement guide

Free download PDF
1.23 MB
How to change front lower arm on FORD MONDEO III Saloon (B4Y) – replacement guide

Free download PDF
2.06 MB
How to change track rod end on FORD MONDEO III Saloon (B4Y) – replacement guide

Free download PDF
1.47 MB

How to change front anti roll bar links on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
1.33 MB
How to change rear anti roll bar links on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
1.24 MB
How to change front anti roll bar links on FORD MONDEO III Estate (BWY) – replacement guide

Free download PDF
1.31 MB
How to change rear anti roll bar links on Ford Mondeo Mk3 saloon – replacement guide

Free download PDF
1.23 MB
How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on Ford Focus MK2 – replacement guide

Free download PDF
1.99 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY rear axle restoration | Drivetrain restoration – Part 2

7K views

Published on: 07/11/2024
Understanding Airbag Light Warnings | Essential Tips for Car Safety

6K views

Published on: 10/04/2023
Save Money on Fuel with These Easy Tips | AUTODOC

5K views

Published on: 27/09/2022
Top 5 reasons why your car squeals | AUTODOC Tips

10K views

Published on: 26/10/2023