Important!

This replacement procedure can be used for:
FORD MONDEO III (B5Y) 1.8 16V, FORD MONDEO III (B5Y) 1.8 16V, FORD MONDEO III (B5Y) 2.0 16V, FORD MONDEO III (B5Y) 2.5 V6 24V, FORD MONDEO III (B5Y) 2.0 16V DI / TDDi / TDCi, FORD MONDEO III (B5Y) 2.0 16V TDDi / TDCi, FORD MONDEO III (B5Y) 2.0 TDCi, FORD MONDEO III (B5Y) ST220, FORD MONDEO III (B5Y) 1.8 SCi, FORD MONDEO III (B5Y) 2.2 TDCi, FORD MONDEO III (B5Y) 3.0 V6 24V … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – FORD MONDEO III (B5Y). Tools you need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #17
                    
                      Drive socket # 17
                    
                      Wheel impact socket #19
                    
                      Ratchet wrench
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on FORD MONDEO III (B5Y) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – FORD MONDEO III (B5Y) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. FORD MONDEO III (B5Y)
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 8

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 9

Remove the stabiliser link.

Replacement: anti roll bar links – FORD MONDEO III (B5Y). Tip from AUTODOC:
Examine stabiliser bushes. Replace them if needed.
Step 10

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 11

Ιnstall the transverse stabilizer link.
Step 12

Tighten the stabiliser link fastener. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 13

Tighten the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #17. Use a torque wrench. Tighten it to 48 Nm torque.
Step 14

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use a drive socket #17. Use a torque wrench. Tighten it to 48 Nm torque.
Step 15

Treat all joints of the stabiliser link. Use copper grease.
Step 16

Clean the wheel rim mounting seat. Use a wire brush.

Step 17

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 18

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – FORD MONDEO III (B5Y). After applying the spray, wait a few minutes.
Step 19

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. FORD MONDEO III (B5Y)
Step 20

Screw in the wheel bolts. Use wheel impact socket #19.
Step 21

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 90 Nm torque.
Step 22

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the FORD Mondeo Mk3 Hatchback (B5Y) model

Ford Mondeo Mk3 tyre size

How to change front lower arm on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
2.06 MB
How to change front wheel bearing on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
3.7 MB
How to change rear wheel bearing on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
2.62 MB
How to change front strut mount on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
4.02 MB
How to change rear anti roll bar links on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
1.24 MB
How to change track rod end on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
1.47 MB

How to change rear anti roll bar links on FORD MONDEO III (B5Y) – replacement guide

Free download PDF
1.24 MB
How to change front anti roll bar links on FORD MONDEO III Estate (BWY) – replacement guide

Free download PDF
1.31 MB
How to change rear anti roll bar links on Ford Mondeo Mk3 saloon – replacement guide

Free download PDF
1.23 MB
How to change front anti roll bar links on Ford Mondeo Mk3 saloon – replacement guide

Free download PDF
1.29 MB
How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on Ford Focus MK2 – replacement guide

Free download PDF
1.99 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to tighten cylinder head bolts

14K views

Published on: 06/03/2025
5 easy car repairs you can do without a garage visit

5K views

Published on: 09/10/2025
DIY jack restoration | AUTODOC tips

24K views

Published on: 22/09/2022
Top 5 possible reasons your car is shaking or vibrating

6K views

Published on: 14/02/2025