Important!
This replacement procedure can be used for:
PEUGEOT 206 CC (2D) 2.0 S16, PEUGEOT 206 CC (2D) 1.6 16V (2DNFUF, 2DNFUR), PEUGEOT 206 CC (2D) 1.6 HDi 110 View more

The steps may slightly vary depending on the car design.

How to change tie rod end / track rod end on PEUGEOT 206 1 (2D) [TUTORIAL AUTODOC]

video
All the parts you need to replace – Track Rod End for 206 CC (2D) and other PEUGEOT models
How to change Track rod end on Peugeot 206 cc 2d 1.6 16V (2DNFUF, 2DNFUR) – step-by-step instructions for straightforward car repair
Track rod end
How to change Rod Assembly on Peugeot 206 cc 2d 1.6 16V (2DNFUF, 2DNFUR) – step-by-step instructions for straightforward car repair
Rod Assembly
How to change Mounting Kit, tie rod end on Peugeot 206 cc 2d 1.6 16V (2DNFUF, 2DNFUR) – step-by-step instructions for straightforward car repair
Mounting Kit, tie rod end
Tools
Replacement: track rod end – Peugeot 206 CC 2D. Tools you need:
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #20
Combination spanner #22
Drive socket # 17
Wheel impact socket #19
Ratchet wrench
Torque wrench
Vernier caliper
Tap wrench
Hammer
Pin punch
Wheel chock
Replacement: track rod end – Peugeot 206 CC 2D. AUTODOC recommends:
  • Replace tie rod ends in pairs.
  • The replacement procedure is identical for the right and left tie rod ends.
  • Please note: all work on the car – Peugeot 206 CC 2D – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    How to change Track Rod End on Peugeot 206 cc 2d 2000 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 2
    How to replace PEUGEOT 206 CC (2D) 1.6 16V (2DNFUF, 2DNFUR) 2001 Track Rod End - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #19.
  3. Step 3
    Peugeot 206 cc 2d 2.0 S16 2002 Track Rod End replacement: free workshop manuals
    Raise the front of the car and secure on supports.
  4. Step 4
    Changing Track Rod End on PEUGEOT 206 CC (2D) 1.6 2003 by yourself
    Unscrew the wheel bolts.
    Replacement: track rod end – Peugeot 206 CC 2D. Tip:
    To avoid injury, hold up the wheel when unscrewing the bolts.
  5. Step 5
    How to remove PEUGEOT 206 1.6 16V (2DNFUF, 2DNFUR) 2004 Track Rod End - online easy-to-follow instructions
    Remove the wheel.
  6. Step 6
    How to replace Track Rod End on PEUGEOT 206 CC (2D) 2005: download PDF manuals and video instructions
    When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
  7. Step 7
    How hard is it to do yourself: Track Rod End replacement on Peugeot 206 cc 2d 1.6 HDi 110 2006 - download illustrated guide
    Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #22.
  8. Step 8
    Need to know how to renew Track Rod End on PEUGEOT 206 2007? This free workshop manual will help you to do it yourself
    Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
  9. Step 9
    Changing of Track Rod End on Peugeot 206 cc 2d 2008 won't be an issue if you follow this illustrated step-by-step guide
    Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a tap wrench.
  10. Step 10
    PEUGEOT 206 1.6 16V (2DNFUF, 2DNFUR) Track Rod End replacement: online guides and video tutorials
    Disconnect the tie rod end from the steering knuckle. Use a pin punch. Use a hammer.
  11. Step 11
    Replacing Track Rod End on Peugeot 206 cc 2d 2001 1.6 16V (2DNFUF, 2DNFUR) by yourself
    Screw the end out of the tie rod.
  12. Step 12
    206 CC (2D) 1.6 16V (2DNFUF, 2DNFUR) 2002 Track Rod End DIY replacement workshop manual
    Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
  13. Step 13
    How to change Track Rod End on PEUGEOT 206 CC (2D) 2003 - tips and tricks
    Screw on a new tie rod end.
    Replacement: track rod end – Peugeot 206 CC 2D. AUTODOC experts recommend:
    While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
  14. Step 14
    Step-by-step recommendations for DIY replacement Peugeot 206 cc 2d 2004 1.6 16V (2DNFUF, 2DNFUR) Track Rod End
    Connect the tie rod end to the steering knuckle.
  15. Step 15
    DIY replacement of Track Rod End on PEUGEOT 206 CC (2D) 1.6 HDi 110 2005 is not an issue anymore with our step-by-step tutorial
    When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
PEUGEOT 206 CC (2D) Track Rod End replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY PEUGEOT 206 CC (2D) Track Rod End replacement - online guide
Tips & tricks for your PEUGEOT 206 CC (2D)
View more
  • How to change Tie rod end on PEUGEOT 206 CC (2D) 1.6 HDi 110 - replacement tricks
    8 bad driving habits | AUTODOC tips
  • Changing Outer tie rod Peugeot 206 cc 2d 1.6 16V (2DNFUF, 2DNFUR) - Replacement Tips
    How to restore a steering wheel | AUTODOC tips
  • Maintenance Hacks - PEUGEOT 206 CC (2D) 2.0 S16 Track rod end ball joint replacement guide
    How to check your head gasket | AUTODOC
  • Replace Outer tie rod end on Peugeot 206 cc 2d - free video tips
    3 things that cause engine damage | AUTODOC tips