Important!

This replacement procedure can be used for:
VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI, VW SHARAN (7M8, 7M9, 7M6) 2.0, VW SHARAN (7M8, 7M9, 7M6) 2.8 VR6, VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI, VW SHARAN (7M8, 7M9, 7M6) 1.8 T 20V, VW SHARAN (7M8, 7M9, 7M6) 2.0 TDI, VW SHARAN (7M8, 7M9, 7M6) 2.8 V6 24V, VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI, VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI, VW SHARAN (7M8, 7M9, 7M6) 2.0 TDI, VW SHARAN (7M8, 7M9, 7M6) 2.0 LPG, VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI … View more

The steps may slightly vary depending on the car design.

How to change rear wheel bearing on VW SHARAN 1 [TUTORIAL AUTODOC]

All the parts you need to replace – Wheel Bearing for SHARAN (7M8, 7M9, 7M6) and other VW models

Alternative products

Wheel bearing kit

WM 1146 METZGER Wheel bearing kit

21,14 GBP

Shop

SKWB-0180153 STARK Wheel bearing kit

22,07 GBP

Shop

V10-8294 VAICO Wheel bearing kit

22,12 GBP

Shop

QWB1146 QUINTON HAZELL Wheel bearing kit

22,78 GBP

Shop

132131 OPTIMAL Wheel bearing kit

25,31 GBP

Shop

100 598 0278 MEYLE Wheel bearing kit

26,01 GBP

Shop

200795 A.B.S. Wheel bearing kit

26,52 GBP

Shop

VKBA 3450 SKF Wheel bearing kit

31,52 GBP

Shop

R154.42 SNR Wheel bearing kit

31,52 GBP

Shop

26636 MAPCO Wheel bearing kit

31,61 GBP

Shop

Replacement: wheel bearing – VW Sharan 1. Tools you need:

                      Wire brush
                    
                      Nylon cleaning brush
                    
                      WD-40 spray
                    
                      Electronic spray
                    
                      All-purpose cleaning spray
                    
                      Brake cleaner 
                    
                      Anti-squeal paste
                    
                      Ceramic grease
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #15
                    
                      Combination spanner #24
                    
                      Drive socket # 13
                    
                      Drive socket # 18
                    
                      Drive socket # 24
                    
                      HEX bit no.H6
                    
                      Wheel impact socket #19
                    
                      Bearing separator
                    
                      Hub slide hammer puller
                    
                      Ratchet wrench
                    
                      Circlip pliers
                    
                      Tap wrench
                    
                      Bush and bearing driver set
                    
                      Bearing driver tool set
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Do not re-use the bearing assembly of your VW Sharan 1 car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
Please note: all work on the car – VW Sharan 1 – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2

Secure the wheels with chocks.

Step 3

Loosen the wheel hub fastener. Use a drive socket #24. Use a tap wrench.
Step 4

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 5

Raise the car.

Replacement: wheel bearing – VW Sharan 1. AUTODOC experts recommend:
If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
Step 6

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW Sharan 1
Step 7

Remove the wheel.
Step 8

Clean the brake pad wear sensor plug. Use a nylon cleaning brush. Use all-purpose cleaning spray.
Step 9

Detach the connector of the brake pad wear sensor.
Step 10

Clean the brake caliper retaining spring. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
After applying the spray, wait a few minutes.
Step 11

Detach the brake caliper retaining spring. Use a crowbar.
Step 12

Clean the brake caliper fasteners. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
After applying the spray, wait a few minutes.
Step 13

Unscrew the brake caliper fasteners. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench.
Step 14

Remove the fastening bolts.
Step 15

Remove the brake caliper. Use a crowbar.

Replacement: wheel bearing – VW Sharan 1. Professionals recommend:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Step 16

Remove the brake pads.
Step 17

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 18

Unscrew the caliper bracket fastening. Use a drive socket #18. Use a ratchet wrench.
Step 19

Remove the fastening bolts.
Step 20

Remove the caliper bracket.
Step 21

Clean the brake disc fastener. Use a wire brush. Use WD-40 spray.
Step 22

Unscrew the brake disc fastening. Use HEX No.H6. Use a ratchet wrench.
Step 23

Remove the fastening bolt.
Step 24

Remove the brake disc.
Step 25

Unscrew the wheel hub fastener. Use a combination spanner #24. Use a drive socket #24. Use a tap wrench.
Step 26

Remove the fastening bolt.
Step 27

Remove the spring washer with a reluctor ring.
Step 28

Remove the wheel hub. Use the hub slide hammer puller.
Step 29

Clean the wheel hub bearing retaining ring. Use a wire brush. Use WD-40 spray.
Step 30

Remove the wheel hub bearing retaining ring. Use circlip pliers.
Step 31

Press out the wheel hub bearing. Use a bearing driver tool set.
Step 32

Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
Step 33

Press the new bearing into the rear knuckle. Use a bearing driver tool set.

Replacement: wheel bearing – VW Sharan 1. AUTODOC recommends:
Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
Step 34

Install the wheel hub bearing retaining ring. Use circlip pliers.
Step 35

Dismantle the inner bearing race that is remaining on the hub. Bush and bearing driver set. Use a bearing separator.
Step 36

Clean the wheel hub mounting seat.
Step 37

Press the hub into the rear knuckle. Use a bearing driver tool set.
Step 38

Install the spring washer with a reluctor ring.
Step 39

Install the fastening bolt.

Step 40

Screw in the wheel hub fastener. Use a combination spanner #24. Use a drive socket #24. Use a ratchet wrench.
Step 41

Treat the wheel hub fastener. Use copper grease.

Step 42

Clean the hub. Use a wire brush. Use all-purpose cleaning spray.
Step 43

Treat the contacting surface. Use ceramic grease.
Step 44

Install the brake disc.
Step 45

Install the fastening bolt.
Step 46

Tighten the brake disc fastening. Use HEX No.H6. Use a torque wrench. Tighten it to 10 nm torque.
Step 47

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – VW Sharan 1. After applying the spray, wait a few minutes.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 48

Install the brake caliper bracket.
Step 49

Install the fastening bolts.
Step 50

Tighten the brake caliper bracket fasteners. Use a drive socket #18. Use a torque wrench. Tighten it to 110 nm torque.
Step 51

Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.

Replacement: wheel bearing – VW Sharan 1. Tip:
Make sure the disc surface is clean before installing the pads.
Step 52

Install the brake pads.
Step 53

Install the brake caliper and fix it.
Step 54

Install the fastening bolts.
Step 55

Tighten the brake caliper fasteners. Use a combination spanner #15. Use a drive socket #13. Use a torque wrench. Tighten it to 35 nm torque.
Step 56

Treat the brake pad wear sensor plug. Use dielectric grease.
Step 57

Attach the connector of the brake pad wear sensor.
Step 58

Install the brake caliper retaining spring. Use a crowbar.
Step 59

Treat the surface where the brake disc contacts the wheel rim. Use ceramic grease.
Step 60

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
After applying the spray, wait a few minutes.
Step 61

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. VW Sharan 1
Step 62

Screw in the wheel bolts. Use wheel impact socket #19.
Step 63

Lower the car.
Step 64

Tighten the hub fastener. Use a combination spanner #24. Use a drive socket #24. Use a torque wrench. Tighten it to 200 Nm torque.

Step 65

Tighten the wheel bolts using a criss-cross pattern. Use wheel impact socket #19. Use a torque wrench. Tighten it to 170 Nm torque.
Step 66

Remove the jacks and chocks.

Replacement: wheel bearing – VW Sharan 1. AUTODOC experts recommend:
Without starting the engine, press the brake pedal several times until you feel significant resistance.Check the brake fluid level in the expansion tank and refill if necessary.
Step 67

Tighten the brake fluid reservoir cap. Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the VW Sharan I (7M8, 7M9, 7M6) model.

VW Sharan 1 tyre size

How to change front strut mount on VW Sharan 1 – replacement guide

Free download PDF
2.7 MB
How to change front wheel bearing on VW Sharan 1 – replacement guide

Free download PDF
3.99 MB
How to change front lower arm on VW Sharan 1 – replacement guide

Free download PDF
1.94 MB
How to change front anti roll bar links on VW Sharan 1 – replacement guide

Free download PDF
1.32 MB
How to change track rod end on VW Sharan 1 – replacement guide

Free download PDF
1.44 MB
How to change front ball joint on VW Sharan 1 – replacement guide

Free download PDF
1.5 MB

How to change rear wheel bearing on VW SHARAN (7N1, 7N2) – replacement guide

Free download PDF
2.22 MB
How to change front wheel bearing on VW SHARAN (7N1, 7N2) – replacement guide

Free download PDF
3.56 MB
How to change front wheel bearing on VW Sharan 1 – replacement guide

Free download PDF
3.99 MB
How to change rear wheel bearing on VW Sharan VAN (7M) – replacement guide

Free download PDF
3.1 MB
How to change wheel bearing on a car – replacement tutorial

Universal

Free download PDF
2.41 MB
How to change front wheel bearing on VW Golf 6 – replacement guide

Free download PDF
3.25 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

5 Tips for New Drivers | AUTODOC tips

3K views

Published on: 31/01/2023
How to put on a steering wheel cover | AUTODOC tips

6K views

Published on: 14/03/2024
Save Money on Fuel with These Easy Tips | AUTODOC

4K views

Published on: 27/09/2022
What causes engine misfire? | AUTODOC

5K views

Published on: 10/07/2020