Important!

This replacement procedure can be used for:
VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI 4motion, VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI … View more

The steps may slightly vary depending on the car design.

How to change front wheel bearing on VW SHARAN 1 [TUTORIAL AUTODOC]

All the parts you need to replace – Wheel Bearing for SHARAN (7M8, 7M9, 7M6) and other VW models

Wheel Bearing Kit

Wheel Bearing

Wheel Bearing Kit for VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI 4motion Diesel (115 hp)

Simple DIY car repair steps – Replacing Wheel Bearing Kit on VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI

Wheel Bearing Kit for VW SHARAN (7M8, 7M9, 7M6) 1.9 TDI Diesel (130 hp)

Replacement: wheel bearing – VW Sharan 1. Tools you might need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Electronic spray
                      
                        All-purpose cleaning spray
                      
                        Brake cleaner 
                      
                        Ceramic grease
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Drive socket # 18
                      
                        Drive socket # 27
                      
                        Shock absorber socket
                      
                        HEX bit no.H6
                      
                        HEX bit no.H8
                      
                        Wheel impact socket #19
                      
                        Ball joint puller
                      
                        Ratchet wrench
                      
                        Tap wrench
                      
                        Circlip pliers
                      
                        Bush and bearing driver set
                      
                        Crow bar
                      
                        Hydraulic transmission jack
                      
                        Wheel chock

Buy tools

AUTODOC recommends:

Do not re-use the bearing assembly of your VW Sharan 1 car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
Please note: all work on the car – VW Sharan 1 – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet.Unscrew the brake fluid reservoir cap.
Step 2

Secure the wheels with chocks.

Step 3

Loosen the fastener of the driveshaft. Use a drive socket #27.Use a tap wrench.
Step 4

Loosen the wheel mounting bolts.Use wheel impact socket #19.
Step 5

Raise the car.

Replacement: wheel bearing – VW Sharan 1. Tip:

If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
Step 6

Unscrew the wheel bolts.

AUTODOC recommends:

Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW Sharan 1
Step 7

Remove the wheel.
Step 8

Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush.Use WD-40 spray.
Step 9

Unscrew the end fastening nut to the steering knuckle.Use a drive socket #18.Use a ratchet wrench.
Step 10

Disconnect the tie rod end from the steering knuckle.Use a ball joint puller.
Step 11

Disconnect the ABS sensor wiring.
Step 12

Detach the brake hose from the shock strut.
Step 13

Detach the ABS sensor connector.
Step 14

Spread the brake pads.Use a crowbar.
Step 15

Clean the brake caliper bracket fasteners. Use a wire brush.Use WD-40 spray.
Step 16

Unscrew the caliper bracket fastening.Use a drive socket #27.Use a ratchet wrench.
Step 17

Remove the fastening bolts.
Step 18

Remove the brake caliper together with its bracket.

Replacement: wheel bearing – VW Sharan 1. Tip from AUTODOC experts:

Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Step 19

Clean the brake disc fastener.Use a wire brush.Use WD-40 spray.

Step 20

Unscrew the brake disc fastening.Use HEX No.H6.Use a ratchet wrench.
Step 21

Remove the fastening bolt.
Step 22

Remove the brake disc.
Step 23

Unscrew the fastener connecting the drive shaft to the wheel hub.Use a drive socket #27.Use a ratchet wrench.
Step 24

Remove the fastening bolt.
Step 25

Clean the fasteners that connect the ball joint to the steering knuckle.Use a wire brush.Use WD-40 spray.
Step 26

Unscrew the ball joint fasteners from the steering knuckle.Use HEX No.H8.Use a ratchet wrench.
Step 27

Remove the fastening bolts.
Step 28

Disconnect the ball joint from the steering knuckle.
Step 29

Detach the driveshaft from the steering knuckle.

Replacement: wheel bearing – VW Sharan 1. AUTODOC recommends:

Make sure that the drive shaft is not unloaded (when the car is jacked).
Step 30

Prop up the steering knuckle.Use a hydraulic transmission jack.
Step 31

Clean the lower fastener connecting the suspension strut to the steering knuckle.Use a wire brush.Use WD-40 spray.
Step 32

Unscrew the lower fastener connecting the shock strut to the steering knuckle.Use a drive socket #18.Use a ratchet wrench.
Step 33

Remove the fastening bolt.
Step 34

Release the lower fastener connecting the shock strut to the steering knuckle. Use a special drive socket to remove the shock absorber.
Step 35

Disconnect the steering knuckle from the shock absorber strut.
Step 36

Remove the steering knuckle together with the wheel hub.
Step 37

Remove the wheel hub from the steering knuckle.Use a bush and bearing driver set.
Step 38

Clean the wheel hub bearing retaining ring.Use a wire brush.Use WD-40 spray.

Step 39

Remove the wheel hub bearing retaining ring.Use circlip pliers.
Step 40

Press out the wheel hub bearing.Use a bush and bearing driver set.
Step 41

Clean the hub bearing mounting seat.Use a wire brush.Use WD-40 spray.
Step 42

Press-fit the new bearing into the steering knuckle.Use a bush and bearing driver set.

Replacement: wheel bearing – VW Sharan 1. Professionals recommend:

Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
Step 43

Install the wheel hub bearing retaining ring.Use circlip pliers.
Step 44

Clean the hub bearing mounting seat.Use a wire brush.Use WD-40 spray.
Step 45

Install the wheel hub on the steering knuckle.Use a bush and bearing driver set.
Step 46

Clean the mounting seats of the shock strut.Use a wire brush.Use WD-40 spray.
Step 47

Clean the splines of the drive shaft CV joint. Use a wire brush.Use WD-40 spray.
Step 48

Treat the splines of the driveshaft CV joint. Use copper grease.
Step 49

Clean the fasteners that connect the ball joint to the steering knuckle.Use a wire brush.Use WD-40 spray.
Step 50

Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush.Use WD-40 spray.
Step 51

Install the steering knuckle assembled with the wheel hub.
Step 52

Fix the shock absorber strut on the steering knuckle.
Step 53

Install the fastening bolt.
Step 54

Remove the support from under the steering knuckle.

AUTODOC recommends:

Replacement: wheel bearing – VW Sharan 1. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.

Step 55

Install the drive shaft.
Step 56

Connect the ball joint to the steering knuckle.
Step 57

Install the fastening bolt.
Step 58

Screw in the fastener of the CV axle.Use a drive socket #27.Use a ratchet wrench.
Step 59

Install the fastening bolts.

Step 60

Screw in the fasteners that connect the ball joint to the steering knuckle.Use HEX No.H8.Use a ratchet wrench.
Step 61

Clean the hub.Use a wire brush.Use all-purpose cleaning spray.
Step 62

Treat the contacting surface.Use ceramic grease.
Step 63

Install the brake disc.
Step 64

Install the fastening bolt.
Step 65

Tighten the brake disc fastening.Use HEX No.H7.Use a torque wrench.Tighten it to 10 nm torque.
Step 66

Clean the mounting seat of the brake caliper bracket.Use a wire brush.Use WD-40 spray.
Step 67

Install the brake caliper together with its bracket.
Step 68

Install the fastening bolts.
Step 69

Connect the tie rod end to the steering knuckle.
Step 70

Screw on the fastening nut that connects the tie rod end to the steering knuckle.Use a drive socket #18.Use a ratchet wrench.
Step 71

Attach the brake hose to the suspension strut.
Step 72

Connect the ABS sensor wiring.
Step 73

Treat the ABS sensor connector.Use dielectric grease.
Step 74

Attach the ABS sensor connector.
Step 75

Tighten the fastening nut connecting the tie rod end to the steering knuckle. Use a drive socket #18.Use a torque wrench.Tighten it to 30 Nm torque.+80°
Step 76

Tighten the fasteners that connect the ball joint to the steering knuckle.Use HEX No.H8.Use a torque wrench.Tighten it to 55 Nm torque.
Step 77

Tighten the brake caliper bracket fasteners.Use a drive socket #27.Use a torque wrench.Tighten it to 200 nm torque.
Step 78

Tighten the lower fasteners of the suspension strut.Use a drive socket #18.Use a torque wrench.Tighten it to 110 nm torque.
Step 79

Treat the fasteners of the ball joint.Use copper grease.
Step 80

Treat the fastener that connects the suspension strut to the steering knuckle.Use copper grease.
Step 81

Treat the fastener connecting the tie rod end to the steering knuckle. Use copper grease.
Step 82

Clean the wheel rim mounting seat.Use a wire brush.
Step 83

Treat the surface where the brake disc contacts the wheel rim. Use ceramic grease.
Step 84

Clean the brake disk surface.Use a brake cleaner.

AUTODOC recommends:

Replacement: wheel bearing – VW Sharan 1. After applying the spray, wait a few minutes.
Step 85

Install the wheel.

AUTODOC recommends:

Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. VW Sharan 1
Step 86

Screw in the wheel bolts.Use wheel impact socket #19.
Step 87

Lower the car.
Step 88

Tighten the CV axle fastener.Use a drive socket #27.Use a torque wrench.Tighten it to 150 Nm torque.+90°
Step 89

Tighten the wheel bolts using a criss-cross pattern.Use wheel impact socket #19.Use a torque wrench.Tighten it to 170 Nm torque.
Step 90

Remove the jacks and chocks.

Replacement: wheel bearing – VW Sharan 1. AUTODOC recommends:

Without starting the engine, press the brake pedal several times until you feel significant resistance.Check the brake fluid level in the expansion tank and refill if necessary.
Step 91

Tighten the brake fluid reservoir cap. Close the hood.

Comment

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

How to change front strut mount on VW Sharan 1 – replacement guide

Free download PDF

11.72 MB
How to change rear anti roll bar bushes on VW Sharan 1 – replacement guide

Free download PDF

3.97 MB
How to change front lower arm on VW Sharan 1 – replacement guide

Free download PDF

7.15 MB
How to change front anti roll bar links on VW Sharan 1 – replacement guide

Free download PDF

1.32 MB
How to change front ball joint on VW Sharan 1 – replacement guide

Free download PDF

1.5 MB
How to change front lower arm on VW Sharan 1 – replacement guide

Free download PDF

1.94 MB

How to change front wheel bearing on VW Sharan II (7N1, 7N2) – replacement guide

Free download PDF

4.5 MB
How to change rear wheel bearing on VW Sharan 1 – replacement guide

Free download PDF

3.26 MB
How to change front wheel bearing on VW Transporter T4 – replacement guide

Free download PDF

11.79 MB
How to change front wheel bearing on VW Passat B5 Variant – replacement guide

Free download PDF

3.03 MB
How to change rear wheel bearing on VW Polo 9N – replacement guide

Free download PDF

2.19 MB
How to change rear wheel bearing on VW Lupo 6X1 – replacement guide

Free download PDF

6.44 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Tips & tricks for your VW SHARAN (7M8, 7M9, 7M6)

How to polish your car | AUTODOC tips

3K views

Published on: 31/03/2022
How to swap the engine on a BMW E30 Turbo | SUPERCAR AUTODOC

2K views

Published on: 02/03/2021
DIY car soundproofing | AUTODOC tips

44K views

Published on: 15/04/2021
Things you should never do with your manual transmission | AUTODOC tips

5K views

Published on: 20/10/2020