Recommended replacement interval for the part category Wheel Brake Cylinder : 60000 km

Important!

This replacement procedure can be used for:
FIAT GRANDE PUNTO (199) 1.3 D Multijet … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Cylinder for GRANDE PUNTO (199) and other FIAT models

Wheel Brake Cylinder

Wheel Brake Cylinder for Grande Punto Hatchback (199) Diesel (69 hp)

Replacement: wheel cylinder – FIAT GRANDE PUNTO (199). Tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Copper grease 
                      
                        Drive socket # 10 
                      
                        Drive socket # 12 
                      
                        Combination spanner №8
                      
                        Flare Nut Wrench № 11
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Tap wrench
                      
                        Flat screwdriver
                      
                        Wheel chock

Buy tools

Replacement: wheel cylinder – FIAT GRANDE PUNTO (199). AUTODOC experts recommend:

Replace the wheel brake cylinders of the rear drum brakes in pairs.
The replacement procedure is identical for the right and left wheel brake cylinders of the rear drum brakes.
All work should be done with the engine stopped.

Replacement: wheel cylinder – FIAT GRANDE PUNTO (199). Take the following steps:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.

Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: wheel cylinder – FIAT GRANDE PUNTO (199). Tip from AUTODOC:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6.1

Unscrew the brake drum fastening.

Step 6.2

Use a drive socket #12.
Step 6.3

Use a ratchet wrench.

Step 7

Remove the brake drum.

Replacement: wheel cylinder – FIAT GRANDE PUNTO (199). AUTODOC recommends:
Examine the brake drum. Replace it if necessary.
Step 8

Disconnect the hydraulic line from the wheel cylinder back. Use a flare nut spanner #11.

Replacement: wheel cylinder – FIAT GRANDE PUNTO (199). Professionals recommend:
Immediately plug the brake line open end to prevent fluid leakage and ingress of dirt into the hydraulic system.
Step 9

Unscrew the brake cylinder fastening bolt. Use a drive socket #10. Use a ratchet wrench.
Step 10.1

Remove the brake cylinder from the backplate.

Step 10.2

Use a flat screwdriver.
Step 11

Clean the brake drum. Use a wire brush. Use WD-40 spray.

Step 12

Clean the brake pipe attachment spot and the brake drum fastening bolts on :maker :model.

Step 13.1

Install a new brake cylinder.

Step 13.2

Use a flat screwdriver.
Step 14

Screw the brake cylinder fastening bolts. Use a drive socket #10. Use a ratchet wrench.
Step 15

Connect the hydraulic line to the wheel cylinder back. Use a flare nut spanner #11.
Step 16

Bleed the brake cylinder system. Use a combination spanner #8.

Replacement: wheel cylinder – FIAT GRANDE PUNTO (199). Tip:
Make sure to set the protection cap on the bleeder valve.
Step 17

Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.

Step 18

Install the brake drum and fasten it.
Step 19

Tigten the brake drum fasteners. Use a drive socket #12. Use a torque wrench. Tighten it to 15 Nm torque.
Step 20

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.

Step 21

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. FIAT GRANDE PUNTO (199)
Step 22

Screw in the wheel bolts. Use wheel impact socket #17.
Step 23

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 98 nm torque.

Step 24

Remove the jacks and chocks.

Replacement: wheel cylinder – FIAT GRANDE PUNTO (199). Tip from AUTODOC experts:
Bleed the brake system after replacing the cylinder on FIAT GRANDE PUNTO (199).Check the brake fluid level in the expansion tank and refill if necessary.Perform test braking when driving at an average speed, the FIAT GRANDE PUNTO (199) should not pull to one side.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the FIAT Grande Punto Hatchback (199) model.

Browse tyres

How to change front brake discs on Fiat Punto 199 – replacement guide

Free download PDF
2.19 MB
How to change front brake pads on Fiat Punto 199 – replacement guide

Free download PDF
1.7 MB
How to change brake drum on FIAT GRANDE PUNTO (199) – replacement guide

Free download PDF
1.72 MB
How to change rear brake shoes on FIAT GRANDE PUNTO (199) – replacement guide

Free download PDF
1.92 MB
How to change rear wheel bearing on FIAT GRANDE PUNTO (199) – replacement guide

Free download PDF
2.44 MB
How to change serpentine belt on Fiat Punto 199 – replacement guide

Free download PDF
1.82 MB

How to change wheel cylinder on a car – replacement tutorial

Universal

Free download PDF
1.96 MB
How to change wheel cylinder on Fiat Punto 188 – replacement guide

Free download PDF
1.3 MB
How to change wheel cylinder on Opel Corsa S93 – replacement guide

Free download PDF
2.08 MB
How to change wheel cylinder on VW Lupo 6X1 – replacement guide

Free download PDF
1.45 MB
How to change wheel cylinder on OPEL Corsa Utility Pickup – replacement guide

Free download PDF
2.08 MB
How to change wheel cylinder on OPEL Ascona C Saloon (J82) – replacement guide

Free download PDF
2.07 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to repair a bumper yourself | AUTODOC tips

9K views

Published on: 01/06/2023
What to do if the airbag light is on | AUTODOC tips

5K views

Published on: 10/04/2023
How to polish your car | AUTODOC tips

5K views

Published on: 31/03/2022
How to replace the suspension on a BMW E30 Turbo | SUPERCAR AUTODOC

1K views

Published on: 04/03/2021