Important!

This replacement procedure can be used for:
PEUGEOT 207 CC (WD_) 1.6 16V, PEUGEOT 207 CC (WD_) 1.6 16V Turbo, PEUGEOT 207 CC (WD_) 1.6 HDi, PEUGEOT 207 CC (WD_) 1.6 HDi, PEUGEOT 207 CC (WD_) 1.6 16V Turbo … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Track Rod End for 207 CC (WD_) and other PEUGEOT models

Track rod end

Rod Assembly

Repair Kit, tie rod

Mounting Kit, tie rod end

        Track rod end for PEUGEOT 207 CC (WD_) 1.6 16V Petrol (120 hp)
      
        Track rod end for PEUGEOT 207 CC (WD_) 1.6 16V Turbo Petrol (150 hp)
      
        Track rod end for PEUGEOT 207 CC (WD_) 1.6 HDi Diesel (109 hp)
      
        Track rod end for PEUGEOT 207 CC (WD_) 1.6 HDi Diesel (112 hp)
      
        Track rod end for PEUGEOT 207 CC (WD_) 1.6 16V Turbo Petrol (156 hp)

Replacement: track rod end – PEUGEOT 207 CC (WD_). Tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Drive socket # 16 
                      
                        Drive socket # 17 
                      
                        Combination spanner #24
                      
                        Combination spanner #25
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Tap wrench
                      
                        Vernier caliper
                      
                        Ball joint puller
                      
                        Wheel chock

Buy tools

Replacement: track rod end – PEUGEOT 207 CC (WD_). AUTODOC recommends:

Replace tie rod ends in pairs.
The replacement procedure is identical for the right and left tie rod ends.
All work should be done with the engine stopped.

Replacement: track rod end – PEUGEOT 207 CC (WD_). Take the following steps:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. PEUGEOT 207 CC (WD_)
Step 5

Remove the wheel.
Step 6

Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 7

When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
Step 8

Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #24 (2 pieces).
Step 9

Unscrew the end fastening nut to the steering knuckle. Use a drive socket #16. Use a tap wrench.
Step 10

Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
Step 11

Screw the end out of the tie rod.
Step 12

Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
Step 13

Screw on a new tie rod end.

Replacement: track rod end – PEUGEOT 207 CC (WD_). Tip from AUTODOC experts:
While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
Step 14

Connect the tie rod end to the steering knuckle.
Step 15

Screw on the fastening nut that connects the tie rod end to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
Step 16

Tighten the fastening nut connecting the tie rod end to the steering knuckle. Use a drive socket #17. Use a torque wrench. Tighten it to 35 nm torque.
Step 17

When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
Step 18

Tighten the tie rod end locknut. Use a combination spanner #24. Use a combination spanner #25. Use a torque wrench. Tighten it to 75 nm torque.
Step 19

Treat the fastener connecting the tie rod end to the steering knuckle. Use copper grease.
Step 20

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 21

Clean the brake disk surface. Use a brake cleaner.

Replacement: track rod end – PEUGEOT 207 CC (WD_). Tip:
After applying the spray, wait a few minutes.
Step 22

Install the wheel.

AUTODOC recommends:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 23

Screw in the wheel bolts. Use wheel impact socket #17.
Step 24

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 100 nm torque.

Replacement: track rod end – PEUGEOT 207 CC (WD_). Tip from AUTODOC:
Check and adjust wheel alignment if necessary.
Step 25

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

How to change front wheel bearing on PEUGEOT 207 CC – replacement guide

Free download PDF
5.97 MB
How to change front anti roll bar links on PEUGEOT 207 CC – replacement guide

Free download PDF
1.25 MB
How to change rear wheel bearing on PEUGEOT 207 CC – replacement guide

Free download PDF
2.15 MB
How to change front brake pads on PEUGEOT 207 CC – replacement guide

Free download PDF
1.26 MB
How to change rear brake pads on PEUGEOT 207 CC – replacement guide

Free download PDF
2.47 MB
How to change rear brake discs on PEUGEOT 207 CC – replacement guide

Free download PDF
2.31 MB

How to change track rod end on Peugeot 207 hatchback – replacement guide

Free download PDF
1.5 MB
How to change track rod end on PEUGEOT 207 SW – replacement guide

Free download PDF
1.44 MB
How to change track rod end on PEUGEOT 207 Saloon – replacement guide

Free download PDF
1.44 MB
How to change track rod end on PEUGEOT 207 SW Box Body / Estate (WK_) – replacement guide

Free download PDF
1.44 MB
How to change track rod end on a car – replacement tutorial

Universal

Free download PDF
1.31 MB
How to change track rod end on Peugeot 206 CC 2D – replacement guide

Free download PDF
1.52 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

What to do if the ABS light comes on | AUTODOC tips

6K views

Published on: 11/03/2021
TOP 8 mistakes car owners make | AUTODOC tips

14K views

Published on: 09/12/2021
How to remove scratches from a car | AUTODOC tips

7K views

Published on: 12/05/2022
How to polish your car | AUTODOC tips

5K views

Published on: 31/03/2022