Important!

This replacement procedure can be used for:
PEUGEOT 207 SW (WK_) 1.6, PEUGEOT 207 SW (WK_) 1.4 Flex, PEUGEOT 207 SW (WK_) 1.6 Flex, PEUGEOT 207 SW (WK_) 1.4, PEUGEOT 207 SW (WK_) 1.4 16V, PEUGEOT 207 SW (WK_) 1.6 16V, PEUGEOT 207 SW (WK_) 1.6 HDi, PEUGEOT 207 SW (WK_) 1.6 HDi, PEUGEOT 207 SW (WK_) 1.6 16V RC, PEUGEOT 207 SW (WK_) 1.6 HDi, PEUGEOT 207 SW (WK_) 1.6 HDi, PEUGEOT 207 SW (WK_) 1.4 16V, PEUGEOT 207 SW (WK_) 1.6 16V Turbo, PEUGEOT 207 SW (WK_) 1.4 LPG … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Track Rod End for 207 SW (WK_) and other PEUGEOT models

Alternative products

Track rod end

Replacement: track rod end – PEUGEOT 207 SW (WK_). Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Drive socket # 16 
                    
                      Drive socket # 17 
                    
                      Combination spanner #24
                    
                      Combination spanner #25
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Tap wrench
                    
                      Vernier caliper
                    
                      Ball joint puller
                    
                      Wheel chock

Buy tools

Replacement: track rod end – PEUGEOT 207 SW (WK_). AUTODOC recommends:

Replace tie rod ends in pairs.
The replacement procedure is identical for the right and left tie rod ends.
All work should be done with the engine stopped.

Replacement: track rod end – PEUGEOT 207 SW (WK_). Take the following steps:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. PEUGEOT 207 SW (WK_)
Step 5

Remove the wheel.
Step 6

Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 7

When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
Step 8

Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #24 (2 pieces).
Step 9

Unscrew the end fastening nut to the steering knuckle. Use a drive socket #16. Use a tap wrench.
Step 10

Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
Step 11

Screw the end out of the tie rod.
Step 12

Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
Step 13

Screw on a new tie rod end.

Replacement: track rod end – PEUGEOT 207 SW (WK_). Tip from AUTODOC experts:
While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
Step 14

Connect the tie rod end to the steering knuckle.
Step 15

Screw on the fastening nut that connects the tie rod end to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
Step 16

Tighten the fastening nut connecting the tie rod end to the steering knuckle. Use a drive socket #17. Use a torque wrench. Tighten it to 35 nm torque.
Step 17

When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
Step 18

Tighten the tie rod end locknut. Use a combination spanner #24. Use a combination spanner #25. Use a torque wrench. Tighten it to 75 nm torque.
Step 19

Treat the fastener connecting the tie rod end to the steering knuckle. Use copper grease.
Step 20

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 21

Clean the brake disk surface. Use a brake cleaner.

Replacement: track rod end – PEUGEOT 207 SW (WK_). Tip:
After applying the spray, wait a few minutes.
Step 22

Install the wheel.

AUTODOC recommends:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 23

Screw in the wheel bolts. Use wheel impact socket #17.
Step 24

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 100 nm torque.

Replacement: track rod end – PEUGEOT 207 SW (WK_). Tip from AUTODOC:
Check and adjust wheel alignment if necessary.
Step 25

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT 207 SW model

Peugeot 207 SW tyre size

How to change front wheel bearing on PEUGEOT 207 SW – replacement guide

Free download PDF
5.97 MB
How to change front anti roll bar links on PEUGEOT 207 SW – replacement guide

Free download PDF
1.25 MB
How to change rear wheel bearing on PEUGEOT 207 SW – replacement guide

Free download PDF
2.15 MB
How to change rear brake pads on PEUGEOT 207 SW – replacement guide

Free download PDF
2.47 MB
How to change front brake pads on PEUGEOT 207 SW – replacement guide

Free download PDF
1.43 MB
How to change rear brake discs on PEUGEOT 207 SW – replacement guide

Free download PDF
2.31 MB

How to change track rod end on Peugeot 207 hatchback – replacement guide

Free download PDF
1.5 MB
How to change track rod end on PEUGEOT 207 CC – replacement guide

Free download PDF
1.44 MB
How to change track rod end on PEUGEOT 207 Saloon – replacement guide

Free download PDF
1.44 MB
How to change track rod end on PEUGEOT 207 SW Box Body / Estate (WK_) – replacement guide

Free download PDF
1.44 MB
How to change track rod end on a car – replacement tutorial

Universal

Free download PDF
1.31 MB
How to change track rod end on Peugeot 206 CC 2D – replacement guide

Free download PDF
1.52 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY brake caliper restoration | AUTODOC tips

747K views

Published on: 02/06/2022
Engine Overheating? Replace Your Cooling Fan to Fix It

6K views

Published on: 15/11/2020
How to make an injector test bench yourself

5K views

Published on: 30/01/2025
Reviving Your Car: How to Start After Extended Idle Time | AUTODOC Tips

7K views

Published on: 20/05/2021