How to change track rod end on Nissan Micra K11 – replacement guide
downloads:
2
Views:
67
0
Users voted – 0
Important!
This replacement procedure can be used for:
NISSAN MICRA II (K11) 1.0 i 16V,
NISSAN MICRA II (K11) 1.5 D,
NISSAN MICRA II (K11) 1.0 i 16V,
NISSAN MICRA II (K11) 1.4 i 16V
…
View more
The steps may slightly vary depending on the car design.
How to change tie rod end / track rod end on NISSAN MICRA 2 [TUTORIAL AUTODOC]
All the parts you need to replace – Track Rod End for MICRA II (K11) and other NISSAN models
Replacement: track rod end – Nissan Micra K11. AUTODOC experts recommend:
Replace tie rod ends in pairs.
The replacement procedure is identical for the right and left tie rod ends.
Please note: all work on the car – Nissan Micra K11 – should be done with the engine switched off.
Carry out replacement in the following order:
Step 1
Secure the wheels with chocks.
Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3
Raise the front of the car and secure on supports.
Step 4
Unscrew the wheel bolts.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Nissan Micra K11
Step 5
Remove the wheel.
Step 6
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
Step 7
Clean the lock nut that connects the tie rod to the tie rod end. Use a wire brush. Use WD-40 spray.
Step 8
Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #19.
Step 9
Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 10
Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
Step 11
Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
Step 12
Screw the end out of the tie rod.
Step 13
Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
Step 14
Screw on a new tie rod end.
Replacement: track rod end – Nissan Micra K11. Tip from AUTODOC experts:
While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
Step 15
Connect the tie rod end to the steering knuckle.
Step 16
Tighten the fastening nut connecting the tie rod end to the steering knuckle. Use a drive socket #17. Use a torque wrench. Tighten it to 45 nm torque.
Step 17
Tighten the tie rod end locknut. Use a combination spanner #19. Use a torque wrench. Tighten it to 65 nm torque.
Step 18
Treat the fastener connecting the tie rod end to the steering knuckle. Use copper grease.
Step 19
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 20
Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends:
Replacement: track rod end – Nissan Micra K11. After applying the spray, wait a few minutes.
Step 21
Install the wheel.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Nissan Micra K11
Step 22
Screw in the wheel bolts. Use wheel impact socket #19.
Step 23
Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 110 nm torque.
Replacement: track rod end – Nissan Micra K11. Tip:
Check and adjust wheel alignment if necessary.
Step 24
Remove the jacks and chocks.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the NISSAN Micra II Hatchback (K11) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your NISSAN MICRA II (K11)
View more
How to paint a car with a spray can | AUTODOC tips
5 Tips for New Drivers | AUTODOC tips
TOP 8 mistakes car owners make | AUTODOC tips
What to do if your car heater isn't working | AUTODOC tips