Recommended replacement interval for the part category Spark plug : 6 year / 90000 km

Important!

This replacement procedure can be used for:
NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.6, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.6, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2.0, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2.0 Allrad … View more

The steps may slightly vary depending on the car design.

How to change spark plug on NISSAN QASHQAI 1 (J10) [TUTORIAL AUTODOC]

All the parts you need to replace – Spark Plug for Qashqai / Qashqai +2 I (J10, NJ10) and other NISSAN models

Alternative products

Spark plug

OE207 CHAMPION Spark plug

8,69 GBP

Shop

062611000069 MAGNETI MARELLI Spark plug

8,94 GBP

Shop

686S0074 RIDEX Spark plug

9,18 GBP

Shop

0 242 135 524 BOSCH Spark plug

10,25 GBP

Shop

SKSP-1990085 STARK Spark plug

11,59 GBP

Shop

5118 NGK Spark plug

12,75 GBP

Shop

91136 NGK Spark plug

14,19 GBP

Shop

Z325 BERU Spark plug

15,66 GBP

Shop

Replacement: spark plugs – Nissan Qashqai J10. Tools you'll need:

                      Electronic spray
                    
                      High-temperature anti-seize lubricant
                    
                      Torque wrench
                    
                      Spark plug socket # 16
                    
                      Drive socket # 8 
                    
                      Drive socket # 10 
                    
                      Ratchet wrench
                    
                      Round-nose pliers
                    
                      Flat screwdriver
                    
                      Telescoping magnet 
                    
                      Fender cover

Buy tools

Replacement: spark plugs – Nissan Qashqai J10. Professionals recommend:

The replacement procedure is the same for all spark plugs.
All work should be done with the engine stopped.

Replacement: spark plugs – Nissan Qashqai J10. Recommended sequence of steps:

Step 1

Open the hood.
Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3

Disconnect the crankcase ventilation hose from the air duct. Use round-nose pliers.
Step 4

Unscrew the clamps and fasteners on the air filter intake pipe. Use a drive socket #10. Use a ratchet wrench.
Step 5

Disconnect the air intake pipe from the air filter housing.
Step 6

Unscrew the fasteners connecting the throttle valve to the intake manifold. Use a drive socket #8. Use a ratchet wrench.
Step 7

Release the clamp and detach the connector and the vacuum hose from the intake manifold near the throttle valve. Use round-nose pliers.
Step 8

Unscrew the fasteners of the intake manifold bracket. Use a drive socket #10.
Step 9

Detach the vacuum booster hose from the intake manifold.
Step 10

Unscrew the intake manifold fasteners. Use a drive socket #10. Use a ratchet wrench.
Step 11

Remove the intake manifold.
Step 12

Cover the intake manifold passages with a microfibre towel to prevent dust and dirt from getting inside.
Step 13

Unscrew the ignition coil bracket. Use a drive socket #10.
Step 14

Take out the ignition coil from the spark plug well.
Step 15

Clean dirt, dust and debris from inside the spark plug well.
Step 16

Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench.
Step 17

Take out the spark plugs. Use a telescoping magnet.
Step 18

Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new spark plugs.
Step 19

Treat the surface of the terminals of the new spark plugs. Use electronic spray.

Step 20

Install the new spark plugs into their mounting seats.
Step 21

Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 19.6 nm torque.

AUTODOC recommends:
Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
Step 22

Install the ignition coil to the spark plug well. Make sure you hear a click indicating that it is locked in place.

Replacement: spark plugs – Nissan Qashqai J10. Tip:
Follow the installation sequence.
Step 23

Tighten the ignition coil fastening. Use a drive socket #10. Use a torque wrench. Tighten it to 7 nm torque.
Step 24

Remove the microfibre towel from the intake manifold.
Step 25

Remove the intake manifold gasket. Use a flat screwdriver.
Step 26

Install the new intake manifold gasket.
Step 27

Install the intake manifold.
Step 28

Tighten the intake manifold fasteners. Use a drive socket #10. Use a torque wrench. Tighten it to 27 nm torque.
Step 29

Tighten the fasteners of the intake manifold bracket. Use a drive socket №10. Use a torque wrench. Tighten it to 10 nm torque.
Step 30

Attach the vacuum booster hose to the intake manifold.
Step 31

Squeeze and install the vacuum booster hose clamp. Use round-nose pliers.
Step 32

Install the throttle valve on the intake manifold.
Step 33

Tighten the throttle valve fasteners. Use a drive socket #8. Use a torque wrench. Tighten it to 10 nm torque.
Step 34

Attach the connector and the vacuum hose to the intake manifold near the throttle valve. Use round-nose pliers.
Step 35

Connect the air intake pipe to the air filter housing.
Step 36

Connect the crankcase ventilation hose to the air duct. Use round-nose pliers.
Step 37

Tighten the clamp and fasteners on the air filter intake pipe. Use a drive socket #10. Use a ratchet wrench.
Step 38

Run the engine for a few minutes. This is necessary in order to make sure that the component operates properly.
Step 39

Shut off the engine.

Step 40

Remove the fender protection cover.
Step 41

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the NISSAN Qashqai / Qashqai+2 I (J10, NJ10) model

Nissan Qashqai j10 tyre size

How to change ignition coil on Nissan Qashqai J10 – replacement guide

Free download PDF
3.06 MB
How to change serpentine belt on NISSAN Qashqai / Qashqai +2 I (J10, NJ10) – replacement guide

Free download PDF
1.64 MB
How to change water pump & timing belt kit on NISSAN Qashqai / Qashqai +2 I (J10, NJ10) – replacement guide

Free download PDF
5.42 MB
How to change glow plugs on NISSAN Qashqai / Qashqai +2 I (J10, NJ10) – replacement guide

Free download PDF
1.55 MB
How to change rear brake pads on Nissan Qashqai J10 – replacement guide

Free download PDF
1.76 MB
How to change front brake pads on Nissan Qashqai J10 – replacement guide

Free download PDF
1.6 MB

How to change spark plugs on a car – replacement tutorial

Universal

Free download PDF
1.74 MB
How to change spark plugs on Nissan Micra K12 – replacement guide

Free download PDF
2.54 MB
How to change spark plugs on Nissan X Trail T30 – replacement guide

Free download PDF
1.2 MB
How to change spark plugs on NISSAN PRIMASTAR Bus (X83) – replacement guide

Free download PDF
1.1 MB
How to change spark plugs on NISSAN Kubistar Van (X76) – replacement guide

Free download PDF
1.1 MB
How to change spark plugs on NISSAN Terrano III (D10) – replacement guide

Free download PDF
1.1 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

#TPMS Explained: Why Your Light is On and How to Respond Safely

8K views

Published on: 28/09/2023
The Fast and Easy Way to Fix a Broken Wheel Stud | AUTODOC tips

9K views

Published on: 08/12/2020
5 tools that make car repair incredibly simple | AUTODOC tips

45K views

Published on: 25/01/2024
How to fix your car with AUTODOC CLUB

16K views

Published on: 30/11/2021