When to replace the Glow Plugs on your NISSAN QASHQAI
Recommended replacement interval for the part category Glow plug : 30000 km
Important!
This replacement procedure can be used for:
NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.5 dCi, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.5 dCi, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.5 dCi View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Tools
Replacement: glow plugs – NISSAN QASHQAI / QASHQAI +2 (J10, JJ10). Tools you might need:
Injector & glow plug grease
Torque wrench
Drive socket # 10
Spark plug socket # 10
Ratchet wrench
Flat Screwdriver
Combination pliers
Crow bar
Microfibre towel
Fender cover
Replacement: glow plugs – NISSAN QASHQAI / QASHQAI +2 (J10, JJ10). AUTODOC recommends:
  • The replacement procedure is identical for all glow plugs.
  • Before getting down to work, start the engine and let it warm up to operating temperature.
  • Wear gloves to protect your hands from hot surfaces.
  • All work should be done with the engine stopped.
Carry out replacement in the following order:
  1. Step 1
    Open the bonnet.
    Step 2
    Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
    Step 3
    How to change Glow Plugs on Nissan Qashqai j10 2006 - free PDF and video manuals
    Disconnect the air intake pipe fastening. Use a drive socket #10. Use a ratchet wrench.
  2. Step 4
    How to replace NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.5 dCi 2007 Glow Plugs - step-by-step manuals and video guides
    Detach the air intake hose clamp. Use combination pliers. Use a crowbar.
  3. Step 5
    Nissan Qashqai j10 2.0 dCi Allrad 2008 Glow Plugs replacement: free workshop manuals
    Remove the air intake pipe.
  4. Step 6
    Changing Glow Plugs on NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2.0 dCi 2009 by yourself
    Cover the air intake hose with a microfibre towel to prevent dust and dirt from getting into the system.
  5. Step 7
    How to remove NISSAN QASHQAI 1.6 dCi 2010 Glow Plugs - online easy-to-follow instructions
    Detach the engine wiring harness. Use a flat screwdriver.
  6. Step 8
    How to replace Glow Plugs on NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2011: download PDF manuals and video instructions
    Unscrew the engine cover fastener. Use a drive socket #10. Use a ratchet wrench.
  7. Step 9
    How hard is it to do yourself: Glow Plugs replacement on Nissan Qashqai j10 2.0 Allrad 2012 - download illustrated guide
    Remove the engine cover.
    Replacement: glow plugs – NISSAN QASHQAI / QASHQAI +2 (J10, JJ10). Tip from AUTODOC experts:
    Do not apply excessive force when removing the part. Otherwise you may damage it.
  8. Step 10
    Need to know how to renew Glow Plugs on NISSAN QASHQAI 2013? This free workshop manual will help you to do it yourself
    Clean dirt, dust and debris from inside the spark plug wells.
  9. Step 11
    Changing of Glow Plugs on Nissan Qashqai j10 2006 won't be an issue if you follow this illustrated step-by-step guide
    Detach the glow plug wiring connectors.
  10. Step 12
    NISSAN QASHQAI 2.0 dCi Allrad Glow Plugs replacement: online guides and video tutorials
    Unscrew the glow plugs. Use the spark plug socket #10. Use a ratchet wrench.
  11. Step 13
    Replacing Glow Plugs on Nissan Qashqai j10 2008 1.5 dCi by yourself
    Remove the glow plugs.
  12. Step 14
    Qashqai / Qashqai +2 I (J10, NJ10) 1.6 dCi 2009 Glow Plugs DIY replacement workshop manual
    Treat the glow plugs. Use the injector & glow plug grease.
    Please note!
    Do not touch the heating element as fingerprints may cause malfunction.
  13. Step 15
    How to change Glow Plugs on NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2010 - tips and tricks
    Install new glow plugs to their mounting seats.
  14. Step 16
    Step-by-step recommendations for DIY replacement Nissan Qashqai j10 2011 1.6 dCi Glow Plugs
    Tighten the glow plugs. Use the spark plug socket #10. Use a torque wrench. Tighten it to 15 nm torque.
    Replacement: glow plugs – NISSAN QASHQAI / QASHQAI +2 (J10, JJ10). Tip from AUTODOC:
    Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 1
Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the NISSAN Qashqai / Qashqai+2 I (J10, NJ10) model.

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
NISSAN Qashqai / Qashqai +2 I (J10, NJ10) Glow Plugs replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
Autodoc CLUB App icon
DIY NISSAN Qashqai / Qashqai +2 I (J10, NJ10) Glow Plugs replacement - online guide
Tips & tricks for your NISSAN Qashqai / Qashqai +2 I (J10, NJ10)
View more
  • How to change Glow plug on NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.6 - replacement tricks
    What causes engine misfire? | AUTODOC
  • Changing Heater plugs Nissan Qashqai j10 1.5 dCi - Replacement Tips
    Regain Your Confidence on the Road: Easy Headlight Restoration Tips
  • Maintenance Hacks - NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2.0 dCi Allrad Heater plug replacement guide
    #TPMS Explained: Why Your Light is On and How to Respond Safely | AUTODOC tips
  • Replace Diesel glow plugs on Nissan Qashqai j10 - free video tips
    Reviving Your Car: How to Start After Extended Idle Time | AUTODOC Tips