Important!

This replacement procedure can be used for:
FORD Tourneo Connect Mk1 1.8 TDCi /TDDi /DI, FORD Tourneo Connect Mk1 1.8 TDCi, FORD Tourneo Connect Mk1 1.8 TDCi … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Engine Mount for Tourneo Connect Mk1 and other FORD models

Engine mount

        Engine mount for Tourneo Connect Mk1 Diesel (75 hp)
      
        Engine mount for Tourneo Connect Mk1 Diesel (90 hp)
      
        Engine mount for Tourneo Connect Mk1 Diesel (110 hp)

Replacement: engine mounts – FORD TOURNEO CONNECT. Tools you might need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Drive socket # 10 
                      
                        Drive socket # 16 
                      
                        Ratchet wrench
                      
                        Flat Screwdriver
                      
                        Jack
                      
                        Fender cover

Buy tools

Replacement: engine mounts – FORD TOURNEO CONNECT. AUTODOC experts recommend:

All work should be done with the engine stopped.

Replacement: engine mounts – FORD TOURNEO CONNECT. Use the following procedure:

Step 1

Open the bonnet.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Unscrew the fasteners of the coolant reservoir. Use a drive socket #10. Use a ratchet wrench.
Step 4

Release the coolant reservoir retainers. Use a flat screwdriver.
Step 5

Remove the coolant reservoir.
Step 6

Support the engine in the oil pan area. Use a jack.
Step 7

Clean the engine mount fasteners. Use a wire brush. Use WD-40 spray.
Step 8

Unscrew the upper fastener of the engine mount. Use a drive socket #16. Use a ratchet wrench.
Step 9

Unscrew the fasteners that connect the engine mount to the car body. Use a drive socket #16. Use a ratchet wrench.
Step 10

Remove the engine mount.

Replacement: engine mounts – FORD TOURNEO CONNECT. Tip from AUTODOC experts:
Carefully check the other engine mounts and replace them if necessary.
Step 11

Clean the mounting seat of the engine mount. Use a wire brush. Use WD-40 spray.
Step 12

Install the engine mount to its mounting seat.
Step 13

Raise the jack by 10–15 cm.
Step 14

Screw in the fasteners that connect the engine mount to the car body. Use a drive socket #16. Use a ratchet wrench.
Step 15

Screw in the upper fastener of the engine mount. Use a drive socket #16. Use a ratchet wrench.
Step 16

Tighten the upper fastener of the engine mount. Use a drive socket #16. Use a torque wrench. Tighten it to 57 Nm torque.
Step 17

Tighten the fasteners that connect the engine mount to the car body. Use a drive socket #16. Use a torque wrench. Tighten it to 57 Nm torque.
Step 18

Treat the engine mount fasteners. Use copper grease.
Step 19

Install the coolant reservoir.
Step 20

Attach the coolant reservoir using its retainers.

Step 21

Screw in the coolant reservoir fasteners. Use a drive socket #10. Use a ratchet wrench.
Step 22

Remove the support from under the engine.

Step 23

Remove the fender protection cover.

Step 24

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the FORD Tourneo Connect Mk1 model.

Browse tyres

How to change serpentine belt on FORD Tourneo Connect – replacement guide

Free download PDF
1.45 MB
How to change spark plugs on FORD TOURNEO CONNECT – replacement guide

Free download PDF
1.48 MB
How to change rear brake pads on FORD TOURNEO CONNECT – replacement guide

Free download PDF
1.71 MB
How to change rear windshield wipers on FORD TOURNEO CONNECT – replacement guide

Free download PDF
593.92 KB
How to change front windshield wipers on FORD TOURNEO CONNECT – replacement guide

Free download PDF
552.96 KB
How to change engine oil and filter on FORD TOURNEO CONNECT – replacement guide

Free download PDF
1.42 MB

How to change engine mounts on a car – replacement tutorial

Universal

Free download PDF
870.4 KB
How to change right engine mounts on Ford Focus MK2 – replacement guide

Free download PDF
1.36 MB
How to change right engine mounts on Ford Focus DAW – replacement guide

Free download PDF
1.58 MB
How to replace the left engine mount on the Ford Transit Mk7 van – replacement guide

Free download PDF
1.26 MB
How to change right engine mounts on FORD FOCUS III Turnier – replacement guide

Free download PDF
1.2 MB
How to change right engine mounts on FORD FOCUS III – replacement guide

Free download PDF
1.19 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Top 5 mistakes when working in the engine bay | AUTODOC tips

7K views

Published on: 04/08/2023
Top 5 reasons why your car squeals | AUTODOC Tips

6K views

Published on: 26/10/2023
TOP 6 WD-40 lifehacks | AUTODOC tips

12K views

Published on: 15/07/2021
5 tools that make car repair incredibly simple | AUTODOC tips

36K views

Published on: 25/01/2024