Important!

This replacement procedure can be used for:
HYUNDAI Grand Santa Fé (DM) 3.3 Allrad, HYUNDAI Grand Santa Fé (DM) 2.2 CRDi Allrad, HYUNDAI Grand Santa Fé (DM) 3.3, HYUNDAI Grand Santa Fé (DM) 3.0 GDi Allrad … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for Grand Santa Fé (DM) and other HYUNDAI models

Wheel bearing kit

        Wheel bearing kit for Grand Santa Fé (DM) Petrol (271 hp)
      
        Wheel bearing kit for Grand Santa Fé (DM) Diesel (200 hp)
      
        Wheel bearing kit for Grand Santa Fé (DM) Petrol (249 hp)
      
        Wheel bearing kit for Grand Santa Fé (DM) Petrol (249 hp)

Replacement: wheel bearing – HYUNDAI GRAND SANTA FÉ. List of the tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        All-purpose cleaning spray
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Combination spanner #18
                      
                        Drive socket # 14
                      
                        Drive socket # 17
                      
                        Drive socket # 18
                      
                        Drive socket # 32
                      
                        Wheel impact socket #21
                      
                        Ratchet wrench
                      
                        Phillips screwdriver
                      
                        Hammer
                      
                        Pin punch
                      
                        Nippers
                      
                        Pliers 
                      
                        Crow bar
                      
                        Wheel chock

Buy tools

AUTODOC recommends:

Do not re-use the bearing assembly of your HYUNDAI GRAND SANTA FÉ car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
Please note: all work on the car – HYUNDAI GRAND SANTA FÉ – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. HYUNDAI GRAND SANTA FÉ
Step 5

Remove the wheel.
Step 6

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.

Step 7

Unscrew the caliper bracket fastening. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 8

Remove the brake caliper together with its bracket.

Replacement: wheel bearing – HYUNDAI GRAND SANTA FÉ. AUTODOC experts recommend:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 9

Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.

Step 10

Unscrew the brake disc mounting bolts and remove it. Use a Phillips screwdriver.
Step 11

Remove the cotter pin securing the hub nut. Use nippers.
Step 12

Unscrew the hub nut. Use a drive socket #32. Use a ratchet wrench.
Step 13

Remove the fastening nut.
Step 14

Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 15

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #19. Use a drive socket #18. Use a ratchet wrench.
Step 16

Remove the fastening bolt. Use a hammer. Use a pin punch.
Step 17

Disconnect the ball joint from the steering knuckle.

Step 18.1

Unscrew the fastener that connects the wheel hub bearing to the steering knuckle.

Step 18.2

Use a drive socket #14. Use a ratchet wrench.
Step 19

Remove the fastening bolts.

Step 20

Detach the driveshaft from the steering knuckle. Use a hammer.

Step 21

Remove the hub and the bearing together, since they are a sealed unit.
Step 22

Clean the wheel hub mounting seat. Use all-purpose cleaning spray.

Step 23

Install the new wheel hub together with the bearing.
Step 24

Install the drive shaft into the wheel hub.

Step 25

Install the fastening bolts.

Step 26.1

Tighten the fastener of the wheel hub bearing.

Step 26.2

Use a combination spanner #14. Use a drive socket #14. Use a torque wrench. Tighten it to 50 Nm torque.
Step 27

Connect the ball joint to the steering knuckle.
Step 28

Install the fastening bolt. Use a hammer.
Step 29

Screw the fastener connecting the ball joint to the steering knuckle. Use a combination spanner #19. Use a drive socket #18. Use a ratchet wrench.

Step 30

Tighten the fastener connecting the ball joint to the steering knuckle. Use a combination spanner #19. Use a drive socket #18. Use a torque wrench. Tighten it to 98 Nm torque.
Step 31

Install the fastening nut.
Step 32

Tighten the wheel hub nut. Use a drive socket #32. Use a torque wrench. Tighten it to 195 Nm torque.
Step 33

Install a new hub nut cotter pin. Use nippers. Use a hammer.
Step 34

Treat the hub where it contacts the brake disk. Use copper grease.

Step 35

Install the new brake disc on the hub and screw in the mounting bolts. Use a Phillips screwdriver.
Step 36

Install the brake caliper together with its bracket.
Step 37

Tighten the brake caliper bracket. Use a combination spanner #17. Use a drive socket #17. Use a torque wrench. Tighten it to 85 Nm torque.
Step 38

Clean the wheel rim mounting seat. Use a wire brush.

Step 39

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 40

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – HYUNDAI GRAND SANTA FÉ. After applying the spray, wait a few minutes.
Step 41

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. HYUNDAI GRAND SANTA FÉ
Step 42

Screw in the wheel bolts. Use wheel impact socket #21.
Step 43

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 108 Nm torque.
Step 44

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the HYUNDAI Grand Santa Fé (DM) model.

Browse tyres

How to change front brake pads on HYUNDAI Grand Santa Fé (DM) – replacement guide

Free download PDF
1.43 MB
How to change fuel filter on Hyundai Santa Fe CM – replacement guide

Free download PDF
2.08 MB
How to change rear brake discs on Hyundai Santa Fe CM – replacement guide

Free download PDF
1.96 MB
How to change front suspension strut on Hyundai Santa Fe CM – replacement guide

Free download PDF
3.1 MB
How to change front brake pads on Hyundai Santa Fe CM – replacement guide

Free download PDF
1.58 MB
How to change front wheel bearing on Hyundai Santa Fe CM – replacement guide

Free download PDF
2.14 MB

How to change front wheel bearing on Hyundai Santa Fe CM – replacement guide

Free download PDF
2.14 MB
How to change rear wheel bearing on Hyundai Santa Fe CM – replacement guide

Free download PDF
1.51 MB
How to change rear wheel bearing on HYUNDAI Santa Fé III (DM) – replacement guide

Free download PDF
1.45 MB
How to change front wheel bearing on HYUNDAI Santa Fé III (DM) – replacement guide

Free download PDF
2.09 MB
How to change front wheel bearing on HYUNDAI SANTA FÉ I (SM) – replacement guide

Free download PDF
2.08 MB
How to change wheel bearing on a car – replacement tutorial

Universal

Free download PDF
2.41 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to repair a chipped or cracked windscreen | AUTODOC tips

7K views

Published on: 14/12/2023
4 reasons why your CHECK ENGINE light is on | AUTODOC tips

6K views

Published on: 30/03/2022
How do EGR valves work? | AUTODOC

18K views

Published on: 18/07/2020
How to reduce fuel consumption | AUTODOC

4K views

Published on: 27/09/2022