How to change front brake pads on Hyundai Santa Fe CM – replacement guide
HYUNDAI SANTA FÉ II (CM) 2.2 CRDi, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi 4x4, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi GLS, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi GLS 4x4, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi 4x4, HYUNDAI SANTA FÉ II (CM) 3.5 4x4, HYUNDAI SANTA FÉ II (CM) 2.0 CRDi, HYUNDAI SANTA FÉ II (CM) 2.4, HYUNDAI SANTA FÉ II (CM) 2.0 CRDi 4x4, HYUNDAI SANTA FÉ II (CM) 2.7 4x4, HYUNDAI SANTA FÉ II (CM) 2.7, HYUNDAI SANTA FÉ II (CM) 2.7 V6 GLS, HYUNDAI SANTA FÉ II (CM) 2.7 V6 GLS 4x4, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi 4x4, HYUNDAI SANTA FÉ II (CM) 2.4 4x4, HYUNDAI SANTA FÉ II (CM) 2.4, HYUNDAI SANTA FÉ II (CM) 2.7 4x4, HYUNDAI SANTA FÉ II (CM) 3.5 4x4, HYUNDAI SANTA FÉ II (CM) 3.5 4x4, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi 4x4, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi, HYUNDAI SANTA FÉ II (CM) 3.5 4x4 … View more
The steps may slightly vary depending on the car design.
How to change front brake discs and front brake pads on HYUNDAI SANTA FÉ CM TUTORIAL | AUTODOC


- Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
- The replacement procedure is identical for all brake pads on the same axle.
- Please note: all work on the car – Hyundai Santa Fe CM – should be done with the engine switched off.
- Step 1

Open the hood. Unscrew the brake fluid reservoir cap.
- Step 2

Secure the wheels with chocks.
- Step 3

Loosen the wheel mounting bolts. Use wheel impact socket #21.
- Step 4

Raise the front of the car and secure on supports.
- Step 5

Unscrew the wheel bolts.
AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Hyundai Santa Fe CM
- Step 6

Remove the wheel.
- Step 7
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 8
Unscrew the brake caliper fastening. Use a drive socket #14. Use a ratchet wrench.
- Step 9
Remove the guide pins from the old brake caliper.
Step 10Spread the brake pads. Use a crowbar.
Step 11
Remove the brake caliper.
Replacement: brake pads – Hyundai Santa Fe CM. AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
- Step 12

Remove the brake pads.
Replacement: brake pads – Hyundai Santa Fe CM. Tip from AUTODOC:Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
- Step 13
Remove the brake pads retaining clips.
Step 14
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
AUTODOC recommends:Replacement: brake pads – Hyundai Santa Fe CM. After applying the spray, wait a few minutes.
- Step 15

Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.
Replacement: brake pads – Hyundai Santa Fe CM. Professionals recommend:Make sure the disc surface is clean before installing the pads.
- Step 16

Install new brake pads.
Replacement: brake pads – Hyundai Santa Fe CM. AUTODOC experts recommend:Make sure the pads are installed with linings facing the disc.
Find out which tyre and wheel sizes are compatible with the HYUNDAI Santa Fe II (CM) model
Popular maintenance tutorials for Hyundai Santa Fe cm
Complete guides for changing the Brake pad set on different HYUNDAI SANTA FE models
Track expenses, manage logs, schedule replacements, and more.
What to do if your check engine light is on | AUTODOC tips
5 Ways You’re Scrubbing Your Car Wrong | AUTODOC Tips
How to make an injector test bench yourself
How to choose a used car and not regret it
Most commonly replaced car parts on HYUNDAI SANTA FE

































