Important!

This replacement procedure can be used for:
FIAT PANDA (169) 1.2 LPG (169.AXB1A), FIAT PANDA (169) 1.1 (169.AXA1A), FIAT PANDA (169) 1.3 D Multijet (169.AXC1A), FIAT PANDA (169) 1.2 Natural Power (169.AXB1A), FIAT PANDA (169) 1.3 D Multijet (169AXG1A, 169AXD1A) … View more

The steps may slightly vary depending on the car design.

How to change front strut mount on FIAT PANDA (169) [TUTORIAL AUTODOC]

Alternative products

Top strut mount

Repair kit, suspension strut

Replacement: strut mount – Fiat Panda 169. Tools you might need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #15
                    
                      Combination spanner #16
                    
                      Combination spanner #27
                    
                      Drive socket # 16 
                    
                      Drive socket # 17 
                    
                      Drive socket # 18 
                    
                      Drive socket # 19 
                    
                      HEX bit No.H6
                    
                      HEX bit No.H7
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Crow bar
                    
                      Hydraulic strut spring compressor
                    
                      Hydraulic transmission jack
                    
                      Fender cover
                    
                      Wheel chock

Buy tools

Replacement: strut mount – Fiat Panda 169. AUTODOC recommends:

The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
All mounts of the front shock struts should be replaced simultaneously.
Please note: all work on the car – Fiat Panda 169 – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet.
Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3

Clean the fasteners of the shock strut upper mount. Use a wire brush. Use WD-40 spray.
Step 4

Loosen the upper fastener of the shock strut mount. Use HEX No.H7. Use a drive socket #19. Use a ratchet wrench.
Step 5

Secure the wheels with chocks.
Step 6

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 7

Raise the front of the car and secure on supports.
Step 8

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Fiat Panda 169
Step 9

Remove the wheel.
Step 10

Detach the brake hose from the shock strut. Disconnect the ABS sensor wiring. Use a crowbar.
Step 11

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 12

Unscrew the fastener connecting the stabilizer link to the shock strut. Use HEX No.H6. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
Step 13

Remove the stabilizer rod.
Step 14

Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 15

Unscrew the fasteners connecting the suspension strut to the steering knuckle. Use a combination spanner #15. Use a drive socket #17. Use a ratchet wrench.
Step 16

Remove the fastening bolt.
Step 17

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 18

Remove the fastening bolt.
Step 19

Disconnect the steering knuckle from the shock absorber strut. Use a crowbar.
Step 20

Unscrew the top fastening of the shock strut mount.

AUTODOC recommends:
Fiat Panda 169 – To avoid injury, hold the suspension strut while unscrewing the fastening bolts.
Step 21

Remove the suspension strut.
Step 22

Set the shock absorber strut on the spring compressor tool.

Replacement: strut mount – Fiat Panda 169. Tip from AUTODOC:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 23

Compress the spring.
Step 24

Treat the shock strut rod. Use a wire brush. Use WD-40 spray.
Step 25

Remove the strut piston rod nut. Use a combination spanner #27. Use HEX No.H7. Use a ratchet wrench.
Step 26

Remove the top strut mount.

AUTODOC recommends:
Replacement: strut mount – Fiat Panda 169. Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
Step 27

Install a new top shock strut mount.
Step 28

Tighten the shock strut piston rod nut. Use a combination spanner #27. Use HEX No.H6. Use a torque wrench. Tighten it to 45 Nm torque.

Replacement: strut mount – Fiat Panda 169. Professionals recommend:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 29

Decompress the spring.
Step 30

Treat the shock strut rod. Use copper grease.
Step 31

Remove the assembled shock strut.
Step 32

Treat the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 33

Install the shock strut into the wheel arch.
Step 34

Screw the top fastening of the shock strut mount. Do not tighten it.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Fiat Panda 169
Step 35

Fix the shock absorber strut on the steering knuckle.
Step 36

Install the fastening bolts.
Step 37

Remove the support from under the steering knuckle.

AUTODOC recommends:
Replacement: strut mount – Fiat Panda 169. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 38

Screw in the fasteners connecting the suspension strut to the steering knuckle. Use a combination spanner #15. Use a drive socket #17. Use a ratchet wrench.
Step 39

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a combination spanner #15. Use a drive socket #17. Use a torque wrench. Tighten it to 75 Nm torque.
Step 40

Connect the ABS sensor wiring.
Step 41

Attach the brake hose. Use a crowbar.
Step 42

Ιnstall the transverse stabilizer link.
Step 43

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #16. Use a torque wrench. Tighten it to 23 Nm torque.
Step 44

Treat the shock strut fasteners. Use copper grease.
Step 45

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 46

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: strut mount – Fiat Panda 169. After applying the spray, wait a few minutes.
Step 47

Install the wheel.

AUTODOC recommends:
Fiat Panda 169 – To avoid injury, hold the suspension strut while screwing in the fastening bolts.
Step 48

Screw in the wheel bolts. Use wheel impact socket #17.
Step 49

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 98 Nm torque.
Step 50

Remove the jacks and chocks.
Step 51

Tighten the upper fastener of the shock absorber strut mount. Use a drive socket #18. Use HEX No.H6. Use a torque wrench. Tighten it to 45 Nm torque.
Step 52

Treat the upper fastener of the suspension strut mount. Use copper grease.
Step 53

Remove the fender protection cover.
Step 54

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the FIAT Panda II Hatchback (169) model

Fiat Panda Mk2 tyre size

How to change front lower arm on Fiat Panda 169 – replacement guide

Free download PDF
1.96 MB
How to change front anti roll bar links on Fiat Panda 169 – replacement guide

Free download PDF
1.28 MB
How to change rear wheel bearing on Fiat Panda 169 – replacement guide

Free download PDF
1.57 MB
How to change front wheel bearing on Fiat Panda 169 – replacement guide

Free download PDF
4.42 MB
How to change front brake pads on Fiat Panda 169 – replacement guide

Free download PDF
2.51 MB
How to change front brake discs on Fiat Panda 169 – replacement guide

Free download PDF
2.17 MB

How to change strut mount on a car – replacement tutorial

Universal

Free download PDF
1.04 MB
How to change front strut mount on Fiat Punto 188 – replacement guide

Free download PDF
1.49 MB
How to change front strut mount on Fiat Bravo 2 – replacement guide

Free download PDF
3.37 MB
How to change front strut mount on FIAT 500 C Convertible (312) – replacement guide

Free download PDF
2.96 MB
How to change front strut mount on FIAT 500 Hatchback (312) – replacement guide

Free download PDF
2.96 MB
How to change front strut mount on FIAT PUNTO Van (188AX) – replacement guide

Free download PDF
2.96 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

#DIY guide: Changing your car's color with a spray can | AUTODOC tips

6K views

Published on: 25/03/2021
5 tools that make car repair incredibly simple | AUTODOC tips

49K views

Published on: 25/01/2024
Extend your engine's life: Avoid these 3 damaging factors | AUTODOC tips

9K views

Published on: 07/10/2021
5 Essential Tips for beginner drivers: Avoid Common Mistakes

4K views

Published on: 31/01/2023