Important!

This replacement procedure can be used for:
HYUNDAI SANTA FÉ II (CM) 2.2 CRDi, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi 4x4, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi GLS, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi GLS 4x4, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi 4x4, HYUNDAI SANTA FÉ II (CM) 2.0 CRDi, HYUNDAI SANTA FÉ II (CM) 2.4, HYUNDAI SANTA FÉ II (CM) 2.0 CRDi 4x4, HYUNDAI SANTA FÉ II (CM) 2.7 4x4, HYUNDAI SANTA FÉ II (CM) 2.7, HYUNDAI SANTA FÉ II (CM) 2.7 V6 GLS, HYUNDAI SANTA FÉ II (CM) 2.7 V6 GLS 4x4, HYUNDAI SANTA FÉ II (CM) 2.2 CRDi 4x4, HYUNDAI SANTA FÉ II (CM) 2.4 4x4 … View more

The steps may slightly vary depending on the car design.

How to change front lower arm on HYUNDAI SANTA FÉ CM TUTORIAL | AUTODOC

All the parts you need to replace – Control Arm for SANTA FÉ II (CM) and other HYUNDAI models

Alternative products

Suspension arm

Replacement: front lower arm – Hyundai Santa Fe CM. Tools you might need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #19
                    
                      Drive socket # 18
                    
                      Drive socket # 19
                    
                      Wheel impact socket #21
                    
                      Ratchet wrench
                    
                      Hammer
                    
                      Pin punch
                    
                      Crow bar
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: front lower arm – Hyundai Santa Fe CM. AUTODOC experts recommend:

The replacement procedure is identical for the left and right lower control arms.
Please note: all work on the car – Hyundai Santa Fe CM – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 3

Raise the front of the car and secure on supports.
Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Hyundai Santa Fe CM
Step 5

Remove the wheel.
Step 6

Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 7

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #19. Use a drive socket #18. Use a ratchet wrench.
Step 8

Remove the fastening bolt. Use a pin punch. Use a hammer.

Step 9

Unscrew the front arm fastener. Use a combination spanner #19. Use a drive socket #19. Use a ratchet wrench.
Step 10

Unscrew the rear fastener connecting the control arm to the subframe. Use a combination spanner #19. Use a drive socket #19. Use a ratchet wrench.
Step 11

Disconnect the ball joint from the steering knuckle. Use a hammer.

Step 12

Remove the rear fastener of the control arm.
Step 13

Remove the front fastener of the control arm.

Step 14

Remove the arm. Use a crowbar.
Step 15

Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
Step 16

Install a new arm. Use a crowbar.

Replacement: front lower arm – Hyundai Santa Fe CM. AUTODOC experts recommend:
During the installation process, use only new bolts and nuts.Do not damage the ball joint cover.
Step 17

Install the control arm fasteners.
Step 18

Connect the ball joint to the steering knuckle. Use a hammer.
Step 19

Install the fastening bolt. Use a hammer.
Step 20

Screw the fastener connecting the ball joint to the steering knuckle. Use a combination spanner #19. Use a drive socket #18. Use a ratchet wrench.

Step 21

Tighten the fastener connecting the ball joint to the steering knuckle. Use a combination spanner #19. Use a drive socket #18. Use a torque wrench. Tighten it to 98 Nm torque.
Step 22

Support the arm. Use a hydraulic transmission jack.
Step 23

Tighten the front fastener connecting the control arm to the subframe. Use a combination spanner #19. Use a drive socket #19. Use a torque wrench. Tighten it to 150 Nm torque.
Step 24

Tighten the rear fastener connecting the arm to the body subframe. Use a combination spanner #19. Use a drive socket #19. Use a torque wrench. Tighten it to 150 Nm torque.
Step 25

Remove the support from under the arm.

AUTODOC recommends:
Replacement: front lower arm – Hyundai Santa Fe CM. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 26

Treat all joints of the arm. Use copper grease.

Step 27

Clean the wheel rim mounting seat. Use a wire brush.

Step 28

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.

AUTODOC recommends:
After applying the spray, wait a few minutes.
Step 29

Clean the brake disk surface. Use a brake cleaner.

Replacement: front lower arm – Hyundai Santa Fe CM. Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 30

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Hyundai Santa Fe CM
Step 31

Screw in the wheel bolts. Use wheel impact socket #21.
Step 32

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 108 Nm torque.
Step 33

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the HYUNDAI Santa Fe II (CM) model

Hyundai Santa Fe cm tyre size

How to change front wheel bearing on Hyundai Santa Fe CM – replacement guide

Free download PDF
2.14 MB
How to change rear wheel bearing on Hyundai Santa Fe CM – replacement guide

Free download PDF
1.51 MB
How to change front anti roll bar links on Hyundai Santa Fe CM – replacement guide

Free download PDF
1.3 MB
How to change track rod end on Hyundai Santa Fe CM – replacement guide

Free download PDF
1.47 MB
How to change front brake pads on Hyundai Santa Fe CM – replacement guide

Free download PDF
1.58 MB
How to change rear brake pads on Hyundai Santa Fe CM – replacement guide

Free download PDF
1.6 MB

How to change control arm on a car – replacement tutorial

Universal

Free download PDF
1.07 MB
How to change front lower arm on Mercedes W203 – replacement guide

Free download PDF
2.02 MB
How to change rear lower arm on Mercedes W204 – replacement guide

Free download PDF
2 MB
How to change front lower arm on Nissan Qashqai J10 – replacement guide

Free download PDF
2.08 MB
How to change rear suspension lower control arm on Nissan Qashqai J10 – replacement guide

Free download PDF
1.84 MB
How to change front lower arm on Mercedes W204 – replacement guide

Free download PDF
1.6 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to prevent car windows from fogging up | AUTODOC tips

13K views

Published on: 04/02/2021
How I started restoring a driveshaft | Drivetrain restoration – Part 1

7K views

Published on: 17/10/2024
How to restore a steering wheel | AUTODOC tips

57K views

Published on: 17/02/2022
Regain Your Confidence on the Road: Easy Headlight Restoration Tips

9K views

Published on: 04/07/2024