Important!

This replacement procedure can be used for:
FIAT STILO Multi Wagon (192) 2.4 20V (19245ZO), FIAT STILO Multi Wagon (192) 1.6 16V, FIAT STILO Multi Wagon (192) 1.8 16V, FIAT STILO Multi Wagon (192) 1.9 JTD, FIAT STILO Multi Wagon (192) 1.9 JTD, FIAT STILO Multi Wagon (192) 1.4 16V, FIAT STILO Multi Wagon (192) 1.4 16V, FIAT STILO Multi Wagon (192) 1.9 D Multijet, FIAT STILO Multi Wagon (192) 1.9 D Multijet (192DXT1B), FIAT STILO Multi Wagon (192) 1.9 D Multijet, FIAT STILO Multi Wagon (192) 1.9 JTD, FIAT STILO Multi Wagon (192) 1.9 JTD, FIAT STILO Multi Wagon (192) 1.9 D, FIAT STILO Multi Wagon (192) 1.6 16V … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Control Arm for STILO Multi Wagon (192) and other FIAT models

Alternative products

Suspension arm

Replacement: front lower arm – FIAT STILO Multi Wagon (192). Tools you need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Copper grease 
                    
                      Combination spanner #17
                    
                      Drive socket # 10 
                    
                      Drive socket # 17 
                    
                      Drive socket # 19 
                    
                      Drive socket # 21 
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Phillips Screwdriver
                    
                      Pin punch
                    
                      Tap wrench
                    
                      Hammer
                    
                      Crow bar
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: front lower arm – FIAT STILO Multi Wagon (192). AUTODOC recommends:

The replacement procedure is identical for the left and right lower control arms.
All work should be done with the engine stopped.

Replacement: front lower arm – FIAT STILO Multi Wagon (192). Recommended sequence of steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: front lower arm – FIAT STILO Multi Wagon (192). Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Unscrew and remove the wheel arch cover fasteners. Use a Phillips screwdriver. Use a drive socket #10. Use a ratchet wrench.
Step 7

Remove the wheel arch cover.
Step 8

Clean the fastener connecting the ball joint to the steering knuckle. Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 9

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 10

Remove the fastening bolt.
Step 11

Unscrew the front arm fastener. Use a drive socket #21. Use a tap wrench.
Step 12

Unscrew the rear arm fastener. Use a drive socket #19. Use a tap wrench.
Step 13

Remove the fastening bolts (2 pieces).
Step 14

Release the fastener connecting the ball joint to the steering knuckle. Use a crowbar. Use a hammer.
Step 15

Disconnect the ball joint from the steering knuckle.
Step 16

Remove the arm. Use a crowbar.
Step 17

Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
Step 18

Install a new arm. Use a pin punch.

Replacement: front lower arm – FIAT STILO Multi Wagon (192). AUTODOC experts recommend:
During the installation process, use only new bolts and nuts.Do not damage the ball joint cover.
Step 19

Connect the ball joint to the steering knuckle.
Step 20

Install the control arm fasteners.
Step 21

Support the arm. Use a hydraulic transmission jack.
Step 22

Install the fastening bolt.

Step 23

Screw the fastener connecting the ball joint to the steering knuckle. Use a drive socket #17. Use a combination spanner #17.
Step 24

Raise the hydraulic transmission jack by 10-15 cm.
Step 25

Tighten the ball joint fastener. Use a drive socket #17. Use a combination spanner #17. Use a torque wrench. Tighten it to 65 nm torque.
Step 26

Tighten the front fastener connecting the control arm to the subframe. Use a drive socket #21. Use a torque wrench. Tighten it to 95 Nm torque.+90°

Replacement: front lower arm – FIAT STILO Multi Wagon (192). Professionals recommend:
Important! Be sure to use new fasteners.
Step 27

Tighten the rear fastener connecting the arm to the body subframe. Use a drive socket #19. Use a torque wrench. Tighten it to 120 nm torque.
Step 28

Remove the support from under the arm.

AUTODOC recommends:
Replacement: front lower arm – FIAT STILO Multi Wagon (192). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 29

Install the wheel arch cover to its mounting seat.
Step 30

Install and tighten the wheel arch cover fasteners. Use a Phillips screwdriver. Use a drive socket #10. Use a ratchet wrench.
Step 31

Treat all joints of the arm. Use copper grease.
Step 32

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 33

Install the wheel.

AUTODOC recommends:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 34

Screw in the wheel bolts. Use wheel impact socket #17.
Step 35

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 120 nm torque.
Step 36

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the FIAT Stilo Multi Wagon (192) model

Fiat Stilo Estate tyre size

How to change front anti roll bar links on FIAT STILO Multi Wagon (192) – replacement guide

Free download PDF
1.7 MB
How to change front strut mount on FIAT Stilo Multi Wagon (192) – replacement guide

Free download PDF
3.18 MB
How to change front brake pads on FIAT Stilo Multi Wagon (192) – replacement guide

Free download PDF
1.82 MB
How to change front brake discs on FIAT STILO Multi Wagon (192) – replacement guide

Free download PDF
2.29 MB
How to change rear brake discs on FIAT STILO Multi Wagon (192) – replacement guide

Free download PDF
2.18 MB
How to change spark plugs on FIAT STILO Multi Wagon (192) – replacement guide

Free download PDF
1.46 MB

How to change front lower arm on FIAT Stilo Box Body / Estate (192) – replacement guide

Free download PDF
2.49 MB
How to change control arm on a car – replacement tutorial

Universal

Free download PDF
1.07 MB
How to change front lower arm on Fiat Panda 169 – replacement guide

Free download PDF
1.96 MB
How to change front lower arm on Fiat Punto 199 – replacement guide

Free download PDF
2.07 MB
How to change front lower arm on Fiat Doblo Cargo – replacement guide

Free download PDF
4.07 MB
How to change front lower arm on Fiat Bravo 2 – replacement guide

Free download PDF
2.56 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

#TPMS Explained: Why Your Light is On and How to Respond Safely

8K views

Published on: 28/09/2023
Kolbenschmidt plastic gauge overview

2K views

Published on: 23/04/2025
Top 5 mistakes when replacing spark plugs | AUTODOC tips

28K views

Published on: 13/07/2023
Which Coolant is Best? Comparison Test | AUTODOC

7K views

Published on: 13/10/2022