Important!

This replacement procedure can be used for:
FIAT Linea (323_, 110_) 1.3 D Multijet (323AXB11, 323AXB1A), FIAT Linea (323_, 110_) 1.4, FIAT Linea (323_, 110_) 1.4 T-Jet (323AXC1A), FIAT Linea (323_, 110_) 1.6 D Multijet … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Control Arm for Linea (323_, 110_) and other FIAT models

Suspension arm

        Suspension arm for Linea (323, 110) Diesel (90 hp)
      
        Suspension arm for Linea (323, 110) Petrol (77 hp)
      
        Suspension arm for Linea (323, 110) Petrol (120 hp)
      
        Suspension arm for Linea (323, 110) Diesel (105 hp)

Replacement: front lower arm – FIAT LINEA (323). Tools you might need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner
                      
                        Copper grease
                      
                        Combination spanner #16
                      
                        Combination spanner #18
                      
                        Drive socket # 16
                      
                        Drive socket # E18
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Flat chisel
                      
                        Hammer
                      
                        Tap wrench
                      
                        Hydraulic transmission jack
                      
                        Wheel chock

Buy tools

Replacement: front lower arm – FIAT LINEA (323). AUTODOC recommends:

The replacement procedure is identical for the left and right lower control arms.
All work should be done with the engine stopped.

Replacement: front lower arm – FIAT LINEA (323). Take the following steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. FIAT LINEA (323)
Step 5

Remove the wheel.
Step 6

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.

Replacement: front lower arm – FIAT LINEA (323). Tip:
After applying the spray, wait a few minutes.Wear protective goggles.
Step 7

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #16. Use a drive socket #16. Use a tap wrench.
Step 8

Remove the fastening bolt.
Step 9

Unscrew the front arm fastener. Use a drive socket #E18. Use a tap wrench.
Step 10

Unscrew the rear fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #E18. Use a tap wrench.
Step 11

Remove the fastening bolts. Use a drive socket #E18. Use a ratchet wrench.
Step 12

Release the fastener connecting the ball joint to the steering knuckle. Use a flat metal-working chisel. Use a hammer.
Step 13

Disconnect the ball joint from the steering knuckle.
Step 14

Remove the arm.
Step 15

Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
Step 16

Install a new arm.

Replacement: front lower arm – FIAT LINEA (323). AUTODOC experts recommend:
During the installation process, use only new bolts and nuts.Do not damage the ball joint cover.
Step 17

Install the fastening bolts. Use a combination spanner #18. Use a drive socket #E18. Use a tap wrench.
Step 18

Screw the rear fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #E18. Use a ratchet wrench.
Step 19

Support the arm. Use a hydraulic transmission jack.
Step 20

Connect the ball joint to the steering knuckle.
Step 21

Install the fastening bolt.
Step 22

Screw the fasteners of the ball joint. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
Step 23

Screw the rear fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #E18. Use a ratchet wrench.
Step 24

Tighten the front fastener connecting the control arm to the subframe. Use a drive socket #E18. Use a torque wrench. Tighten it to 60 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 25

Tighten the rear fastener connecting the arm to the body subframe. Use a drive socket #E18. Use a torque wrench. Tighten it to 60 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 26

Tighten the ball joint fastener. Use a drive socket #16. Use a torque wrench. Tighten it to 50 nm torque.
Step 27

Remove the support from under the arm.

AUTODOC recommends:
Replacement: front lower arm – FIAT LINEA (323). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 28

Treat all joints of the arm. Use copper grease.
Step 29

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 30

Clean the brake disk surface. Use a brake cleaner.

Replacement: front lower arm – FIAT LINEA (323). Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 31

Install the wheel.

Replacement: front lower arm – FIAT LINEA (323). Professionals recommend:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 32

Screw in the wheel bolts. Use wheel impact socket #17.
Step 33

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 nm torque.
Step 34

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the FIAT Linea (323, 110) model.

Browse tyres

How to change front anti roll bar links on FIAT Linea (323_, 110_) – replacement guide

Free download PDF
1.7 MB
How to change rear wheel bearing on FIAT Linea (323_, 110_) – replacement guide

Free download PDF
2.44 MB
How to change front brake pads on FIAT Linea (323, 110) – replacement guide

Free download PDF
1.8 MB
How to change front brake discs on FIAT Linea (323_, 110_) – replacement guide

Free download PDF
2.29 MB
How to change rear brake discs on FIAT Linea (323_, 110_) – replacement guide

Free download PDF
2.18 MB
How to change serpentine belt on FIAT Linea (323, 110) – replacement guide

Free download PDF
1.39 MB

How to change control arm on a car – replacement tutorial

Universal

Free download PDF
1.07 MB
How to change front lower arm on Fiat Panda 169 – replacement guide

Free download PDF
1.96 MB
How to change front lower arm on Fiat Bravo 2 – replacement guide

Free download PDF
2.56 MB
How to change front lower arm on Fiat Doblo Cargo – replacement guide

Free download PDF
4.07 MB
How to change front lower arm on Fiat Punto 199 – replacement guide

Free download PDF
2.07 MB
How to change front lower arm on Fiat Punto 188 – replacement guide

Free download PDF
2.03 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to unlock your car without a key | AUTODOC tips

844K views

Published on: 15/09/2022
Top 5 mistakes when working in the engine bay | AUTODOC tips

7K views

Published on: 04/08/2023
How to check your head gasket | AUTODOC

9K views

Published on: 13/10/2020
How to polish an old engine valve cover to a shiny finish | AUTODOC Tips

8K views

Published on: 30/11/2023