Disclaimer
How to change front anti roll bar links on VW Sharan VAN (7M) – replacement guide
downloads:
2
Views:
13
Important!
This replacement procedure can be used for:
VW Sharan VAN (7M) 1.9 TDI (7M9), VW Sharan VAN (7M) 1.9 TDI (7M6, 7M9), VW Sharan VAN (7M) 1.9 TDI (7M8), VW Sharan VAN (7M) 1.9 TDI (7M8, 7M9), VW Sharan VAN (7M) 2.0 (7M8, 7M9) … View more
The steps may slightly vary depending on the car design.
VW Sharan VAN (7M) 1.9 TDI (7M9), VW Sharan VAN (7M) 1.9 TDI (7M6, 7M9), VW Sharan VAN (7M) 1.9 TDI (7M8), VW Sharan VAN (7M) 1.9 TDI (7M8, 7M9), VW Sharan VAN (7M) 2.0 (7M8, 7M9) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for Sharan VAN (7M) and other VW models
Anti-roll bar link
Alternative products
Anti-roll bar link
Wire brush
WD-40 spray
Brake cleaner
Ceramic grease
Copper grease
Torque wrench
Combination spanner #16
Drive socket # 17
Drive socket # 19
Wheel impact socket #19
Ratchet wrench
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on VW Sharan Kastenwagen (7M) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – VW Sharan Kastenwagen (7M) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3Raise the car.Replacement: anti roll bar links – VW Sharan Kastenwagen (7M). Tip from AUTODOC:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW Sharan Kastenwagen (7M) - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use a drive socket #19. Use a ratchet wrench. - Step 8
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #16. Use a drive socket #19. Use a ratchet wrench. - Step 9
Remove the stabiliser link.AUTODOC recommends:Examine stabiliser bushes. Replace them if needed. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Install a new stabiliser link and tighten the fasteners. - Step 12
Screw in the sway bar link fasteners. Use a combination spanner #16. Use a drive socket #19. Use a ratchet wrench. - Step 13
Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #17. Use a torque wrench. Tighten it to 100 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VW Sharan VAN (7M) model
Popular maintenance tutorials for VW Sharan Kastenwagen (7M)
Free download PDF
1.39 MB
Free download PDF1.46 MB
Free download PDF3.1 MB
Free download PDF1.54 MB
Free download PDF757.76 KB
Free download PDF942.08 KB
Complete guides for changing the Drop links on different VW SHARAN models
Free download PDF1.48 MB
Free download PDF1.15 MB
Free download PDF1.32 MB
Free download PDF972.8 KB
Free download PDF1.99 MB
Free download PDF2.01 MB
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VW Sharan VAN (7M)
View more
Understanding Airbag Light Warnings | Essential Tips for Car Safety
How to make an injector test bench yourself
TOP 5 mistakes during DIY oil change | AUTODOC tips
DIY starter repair | AUTODOC tips
Most commonly replaced car parts on VW SHARAN
Time to replace parts? Get even better deals in our Shop app.
SCAN ME