Important!

This replacement procedure can be used for:
VW POLO (9N_) 1.4 16V, VW POLO (9N_) 1.4 BiFuel, VW POLO (9N_) 1.9 TDI, VW POLO (9N_) 1.4 TDI, VW POLO (9N_) 1.4 16V, VW POLO (9N_) 1.2 12V, VW POLO (9N_) 1.9 SDI, VW POLO (9N_) 1.2, VW POLO (9N_) 1.4 16V, VW POLO (9N_) 1.4 FSI, VW POLO (9N_) 1.9 TDI, VW POLO (9N_) 1.4 TDI, VW POLO (9N_) 1.4 TDI, VW POLO (9N_) 1.8 GTI, VW POLO (9N_) 1.6 16V, VW POLO (9N_) 1.8 GTi Cup Edition, VW POLO (9N_) 1.2, VW POLO (9N_) 1.2 12V, VW POLO (9N_) 1.4 … View more

The steps may slightly vary depending on the car design.

How to change front anti roll bar link / front drop link on VW POLO 4 (9N) [TUTORIAL AUTODOC]

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – VW Polo 9N. Tools you need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Drive socket # 16 
                    
                      Combination spanner #16
                    
                      Torx bit T30
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on VW Polo 9N in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
All work should be done with the engine stopped.

Replacement: anti roll bar links – VW Polo 9N. Recommended sequence of steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.
Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. VW Polo 9N
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.

Step 7

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #16. Use a ratchet wrench.
Step 8

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use Torx T30. Use a ratchet wrench.
Step 9

Remove the stabilizer rod. Use a crowbar.

Replacement: anti roll bar links – VW Polo 9N. AUTODOC experts recommend:
Examine stabiliser bushes. Replace them if needed.
Step 10

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 11

Install a new rod, tighten the fasteners. Use a combination spanner #16. Use a drive socket #16. Use Torx T30. Use a ratchet wrench.
Step 12

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use Torx T30. Use a torque wrench. Tighten it to 40 Nm torque.
Step 13

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #16. Use a torque wrench. Tighten it to 40 Nm torque.
Step 14

Treat all joints of the stabiliser link. Use copper grease.
Step 15

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 16

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – VW Polo 9N. After applying the spray, wait a few minutes.
Step 17

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. VW Polo 9N
Step 18

Screw in the wheel bolts. Use wheel impact socket #17.
Step 19

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 120 Nm torque.
Step 20

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the VW Polo IV Hatchback (9N) model

VW Polo Mk4 tyre size

How to change front lower arm on VW Polo 9N – replacement guide

Free download PDF
2.45 MB
How to change track rod end on VW Polo 9N – replacement guide

Free download PDF
2.23 MB
How to change front strut mount on VW Polo 9N – replacement guide

Free download PDF
2.08 MB
How to change rear strut mount on VW Polo 9N – replacement guide

Free download PDF
1.58 MB
How to change rear wheel bearing on VW Polo 9N – replacement guide

Free download PDF
1.41 MB
How to change front anti roll bar bushes on VW POLO (9N_) – replacement guide

Free download PDF
1.64 MB

How to change front anti roll bar links on VW Polo Hatchback (6R1, 6C1) – replacement guide

Free download PDF
1.25 MB
How to change front anti roll bar links on VW POLO (6N2) – replacement guide

Free download PDF
1 MB
How to change front anti roll bar links on VW Polo VI (AW1, BZ1) – replacement guide

Free download PDF
2.05 MB
How to change front anti roll bar links on VW Polo Hatchback (6N1) – replacement guide

Free download PDF
1 MB
How to change front anti roll bar links on VW Polo 5 – replacement guide

Free download PDF
1.3 MB
How to change front anti roll bar links on VW Polo IV Saloon (9A4, 9A2, 9N2, 9A6) – replacement guide

Free download PDF
2.05 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to restore a steering wheel | AUTODOC tips

63K views

Published on: 17/02/2022
Top 5 reasons why your car squeals | AUTODOC Tips

10K views

Published on: 26/10/2023
What causes engine misfire? | AUTODOC

6K views

Published on: 10/07/2020
What to do if your check engine light is on | AUTODOC tips

19K views

Published on: 19/08/2020