Important!
This replacement procedure can be used for:
VW SHARAN (7N1, 7N2) 2.0 TFSI, VW SHARAN (7N1, 7N2) 2.0 TDI 4motion, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 1.4 TSI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 1.8 TSI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 1.4 TSI, VW SHARAN (7N1, 7N2) 2.0 TSI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 2.0 TDI 4motion, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 2.0 TDI 4motion, VW SHARAN (7N1, 7N2) 2.0 TDI 4motion View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Anti Roll Bar Links for SHARAN (7N1, 7N2) and other VW models
Alternative products
How to change Anti-roll bar link on VW Sharan 7n 2.0 TDI – step-by-step instructions for straightforward car repair Anti-roll bar link
Tools
Replacement: anti roll bar links – VW SHARAN (7N1, 7N2). List of the tools you'll need:
Wire brush
WD-40 spray
Brake cleaner
Ceramic grease
Copper grease
Torque wrench
Combination spanner #18
Combination spanner #19
Drive socket # 18
Drive socket # 19
XZN socket bit #6
HEX bit No.H5
Wheel impact socket #17
Ratchet wrench
Wheel chock
AUTODOC recommends:
  • Replace the stabiliser links on VW SHARAN (7N1, 7N2) in pairs.
  • The replacement procedure is identical for both stabiliser links on the same axle.
  • Please note: all work on the car – VW SHARAN (7N1, 7N2) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    Secure the wheels with chocks.
    Step 2
    How to change Anti Roll Bar Links on VW Sharan 7n 2010 - free PDF and video manuals
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  2. Step 3
    Raise the car.
    Replacement: anti roll bar links – VW SHARAN (7N1, 7N2). Professionals recommend:
    If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
    Step 4
    How to replace VW SHARAN (7N1, 7N2) 2.0 TDI 2011 Anti Roll Bar Links - step-by-step manuals and video guides
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW SHARAN (7N1, 7N2)
  3. Step 5
    VW Sharan 7n 2.0 TDI 4motion 2012 Anti Roll Bar Links replacement: free workshop manuals
    Remove the wheel.
  4. Step 6
    Changing Anti Roll Bar Links on VW SHARAN (7N1, 7N2) 2.0 TDI 2013 by yourself
    Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
  5. Step 7
    How to remove VW SHARAN 2.0 TDI 4motion 2014 Anti Roll Bar Links - online easy-to-follow instructions
    Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #18. Use XZN #6. Use a ratchet wrench.
  6. Step 8
    How to replace Anti Roll Bar Links on VW SHARAN (7N1, 7N2) 2015: download PDF manuals and video instructions
    Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench.
  7. Step 9
    How hard is it to do yourself: Anti Roll Bar Links replacement on VW Sharan 7n 2.0 TDI 2016 - download illustrated guide
    Remove the stabiliser link.
    Replacement: anti roll bar links – VW SHARAN (7N1, 7N2). Tip from AUTODOC experts:
    Examine stabiliser bushes. Replace them if needed.
  8. Step 10
    Need to know how to renew Anti Roll Bar Links on VW SHARAN 2017? This free workshop manual will help you to do it yourself
    Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
  9. Step 11
    Changing of Anti Roll Bar Links on VW Sharan 7n 2018 won't be an issue if you follow this illustrated step-by-step guide
    Install a new stabiliser link and tighten the fasteners. Use a combination spanner #19. Use HEX No.H5. Use a ratchet wrench.
  10. Step 12
    VW SHARAN 1.4 TSI Anti Roll Bar Links replacement: online guides and video tutorials
    Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #19. Use a torque wrench. Tighten it to 65 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?

Find out which tyre and wheel sizes are compatible with the VW Sharan II (7N1, 7N2) model

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY VW SHARAN (7N1, 7N2) Anti Roll Bar Links replacement - online guide
Tips & tricks for your VW SHARAN (7N1, 7N2)
View more
  • How to change Drop links on VW SHARAN (7N1, 7N2) 1.4 TSI - replacement tricks
    How to unlock your car without a key | AUTODOC tips
  • Changing Stabilizer link VW Sharan 7n 2.0 TDI - Replacement Tips
    Engine Overheating? Replace Your Cooling Fan to Fix It
  • Maintenance Hacks - VW SHARAN (7N1, 7N2) 2.0 TDI 4motion Sway bar link replacement guide
    How to fix your car with AUTODOC CLUB
  • Replace Drop link on VW Sharan 7n - free video tips
    Don’t Replace, Just Polish! Headlight Restoration with AUTODOC
Autodoc CLUB App icon
Time to replace parts? Get even better deals in our Shop app.
VW SHARAN (7N1, 7N2) Anti Roll Bar Links replace by yourself - Scan QR-code and download AUTODOC CLUB app
SCAN ME