Important!

This replacement procedure can be used for:
VW SHARAN (7N1, 7N2) 2.0 TFSI, VW SHARAN (7N1, 7N2) 2.0 TDI 4motion, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 1.4 TSI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 1.8 TSI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 1.4 TSI, VW SHARAN (7N1, 7N2) 2.0 TSI, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 2.0 TDI 4motion, VW SHARAN (7N1, 7N2) 2.0 TDI, VW SHARAN (7N1, 7N2) 2.0 TDI 4motion, VW SHARAN (7N1, 7N2) 2.0 TDI 4motion … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Anti Roll Bar Links for SHARAN (7N1, 7N2) and other VW models

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – VW SHARAN (7N1, 7N2). Tools you might need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #16
                    
                      Drive socket # 16 
                    
                      XZN socket bit # 6
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on VW SHARAN (7N1, 7N2) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – VW SHARAN (7N1, 7N2) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW SHARAN (7N1, 7N2)
Step 5

Remove the wheel.
Step 6

Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer bar with the control arm. Use a drive socket #16. Use a ratchet wrench.
Step 8

Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 9

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench.
Step 10

Support the arm. Use a hydraulic transmission jack.
Step 11

Remove the stabilizer rod.
Step 12

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 13

Ιnstall the transverse stabilizer link.
Step 14

Tighten the stabiliser link fastener. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench.
Step 15

Raise the hydraulic transmission jack by 10-15 cm.
Step 16

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use XZN #6. Use a drive socket #16. Use a torque wrench. Tighten it to 45 Nm torque.
Step 17

Tighten the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #16. Use XZN #6. Use a drive socket #16. Use a torque wrench. Tighten it to 45 Nm torque.
Step 18

Treat all joints of the stabiliser link. Use copper grease.
Step 19

Remove the support from under the arm.

AUTODOC recommends:
Replacement: anti roll bar links – VW SHARAN (7N1, 7N2). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 20

Clean the wheel rim mounting seat. Use a wire brush.
Step 21

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 22

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – VW SHARAN (7N1, 7N2). After applying the spray, wait a few minutes.
Step 23

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. VW SHARAN (7N1, 7N2)
Step 24

Screw in the wheel bolts. Use wheel impact socket #17.
Step 25

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.
Step 26

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the VW Sharan II (7N1, 7N2) model

VW Sharan 7n tyre size

How to change rear strut mount on VW Sharan II (7N1, 7N2) – replacement guide

Free download PDF
2.79 MB
How to change rear suspension lower trailing arm on VW Sharan II (7N1, 7N2) – replacement guide

Free download PDF
2.59 MB
How to change front lower arm on VW SHARAN (7N1, 7N2) – replacement guide

Free download PDF
2.13 MB
How to change track rod end on VW Sharan II (7N1, 7N2) – replacement guide

Free download PDF
2.22 MB
How to change rear wheel bearing on VW SHARAN (7N1, 7N2) – replacement guide

Free download PDF
2.22 MB
How to change front wheel bearing on VW SHARAN (7N1, 7N2) – replacement guide

Free download PDF
3.56 MB

How to change front anti roll bar links on VW SHARAN (7N1, 7N2) – replacement guide

Free download PDF
1.15 MB
How to change front anti roll bar links on VW Sharan 1 – replacement guide

Free download PDF
1.32 MB
How to change front anti roll bar links on VW Sharan VAN (7M) – replacement guide

Free download PDF
1.27 MB
How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on VW Polo 9N – replacement guide

Free download PDF
1.99 MB
How to change front anti roll bar links on VW Passat B7 saloon – replacement guide

Free download PDF
2.01 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide

3K views

Published on: 23/03/2023
How to tighten cylinder head bolts

7K views

Published on: 06/03/2025
How to Get the Best Deals on Car Parts | Save Money with AUTODOC

2K views

Published on: 03/02/2022
What to do if your car’s bonnet won’t open | AUTODOC tips

7K views

Published on: 12/09/2024