Disclaimer
How to change front anti roll bar links on VW POLO (6N2) – replacement guide
downloads:
8
Views:
65
Important!
This replacement procedure can be used for:
VW POLO (6N2) 1.9 SDI, VW POLO (6N2) 1.4, VW POLO (6N2) 1.4, VW POLO (6N2) 1.9 D, VW POLO (6N2) 1.7 SDI, VW POLO (6N2) 1.4 16V, VW POLO (6N2) 1.0, VW POLO (6N2) 1.4 TDI, VW POLO (6N2) 1.6 16V GTI, VW POLO (6N2) 1.4 16V … View more
The steps may slightly vary depending on the car design.
VW POLO (6N2) 1.9 SDI, VW POLO (6N2) 1.4, VW POLO (6N2) 1.4, VW POLO (6N2) 1.9 D, VW POLO (6N2) 1.7 SDI, VW POLO (6N2) 1.4 16V, VW POLO (6N2) 1.0, VW POLO (6N2) 1.4 TDI, VW POLO (6N2) 1.6 16V GTI, VW POLO (6N2) 1.4 16V … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for POLO (6N2) and other VW models
Anti-roll bar link
Anti-roll bar link
Anti-roll bar link for Polo III Hatchback (6N2) Diesel (64 hp)
Anti-roll bar link for Polo III Hatchback (6N2) Petrol (60 hp)
Anti-roll bar link for Polo III Hatchback (6N2) Petrol (54 hp)
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Drive socket # 13
Wheel impact socket #17
Ratchet wrench
Torque wrench
Crow bar
Wheel chock
Replacement: anti roll bar links – VW POLO (6N2). Tip from AUTODOC experts:
- Replace the stabiliser links on VW POLO (6N2) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- All work should be done with the engine stopped.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.Replacement: anti roll bar links – VW POLO (6N2). Tip:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 5
Remove the wheel. - Step 6Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.Step 7
Unscrew the fastener connecting the stabilizer bar with the control arm. Use a drive socket #13. Use a ratchet wrench. - Step 8
Remove the stabilizer rod. Use a crowbar. - Step 9Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.Step 10
Install a new rod, tighten the fasteners. Use a crowbar.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 1
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the VW Polo III Hatchback (6N2) model.
Popular maintenance tutorials for VW Polo 6N2
Free download PDF
1.77 MB
Free download PDF3.31 MB
Free download PDF1.59 MB
Free download PDF3.38 MB
Free download PDF2.17 MB
Free download PDF2.19 MB
Complete guides for changing the Drop links on different VW POLO models
Free download PDF1.25 MB
Free download PDF1.99 MB
Free download PDF2.05 MB
Free download PDF1 MB
Free download PDF1.3 MB
Free download PDF1.24 MB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your VW POLO (6N2)
View more
What to do if your check engine light is on | AUTODOC tips
TOP 6 WD-40 lifehacks | AUTODOC tips
Checking the starter without removing it | AUTODOC tips
DIY alternator repair | AUTODOC tips
