Important!

This replacement procedure can be used for:
NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.5 dCi, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.6, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2.0, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2.0 Allrad, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.6 dCi Allrad, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.6 dCi, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.5 dCi, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2.0 dCi, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 2.0 dCi Allrad, NISSAN Qashqai / Qashqai +2 I (J10, NJ10) 1.5 dCi … View more

The steps may slightly vary depending on the car design.

How to change front anti roll bar link on NISSAN QASHQAI (J10, NJ10) [TUTORIAL AUTODOC]

All the parts you need to replace – Anti Roll Bar Links for Qashqai / Qashqai +2 I (J10, NJ10) and other NISSAN models

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – Nissan Qashqai J10. Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #17
                    
                      Combination spanner #19
                    
                      Combination spanner #21
                    
                      Drive socket # 19 
                    
                      Drive socket # 21 
                    
                      Wheel impact socket #21
                    
                      Ratchet wrench
                    
                      Wheel chock

Buy tools

Replacement: anti roll bar links – Nissan Qashqai J10. Tip from AUTODOC experts:

Replace the stabiliser links on Nissan Qashqai J10 in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – Nissan Qashqai J10 – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 3

Raise the front of the car and secure on supports.
Step 4

Unscrew the wheel bolts.

Replacement: anti roll bar links – Nissan Qashqai J10. Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #21. Use a ratchet wrench.
Step 8

Unscrew the fasteners connecting the stabiliser link to the stabiliser bar. Use a combination spanner #17. Use a combination spanner #21.
Step 9

Remove the stabilizer rod.

Replacement: anti roll bar links – Nissan Qashqai J10. AUTODOC recommends:
Examine stabiliser bushes. Replace them if needed.
Step 10

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 11

Install a new rod, tighten the fasteners.
Step 12

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #19. Use a drive socket #19. Use a torque wrench. Tighten it to 65 Nm torque.
Step 13

Tighten the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #19. Use a drive socket #19. Use a torque wrench. Tighten it to 65 Nm torque.
Step 14

Treat all joints of the stabiliser link. Use copper grease.
Step 15

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 16

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – Nissan Qashqai J10. After applying the spray, wait a few minutes.
Step 17

Install the wheel.

Replacement: anti roll bar links – Nissan Qashqai J10. Tip from AUTODOC experts:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 18

Screw in the wheel bolts. Use wheel impact socket #21.
Step 19

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 112 nm torque.
Step 20

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the NISSAN Qashqai / Qashqai+2 I (J10, NJ10) model

Nissan Qashqai j10 tyre size

How to change front wheel bearing on Nissan Qashqai J10 – replacement guide

Free download PDF
3.71 MB
How to change rear suspension lower control arm on Nissan Qashqai J10 – replacement guide

Free download PDF
1.84 MB
How to change front lower arm on Nissan Qashqai J10 – replacement guide

Free download PDF
2.08 MB
How to change track rod end on Nissan Qashqai J10 – replacement guide

Free download PDF
1.44 MB
How to change rear brake pads on Nissan Qashqai J10 – replacement guide

Free download PDF
1.76 MB
How to change front brake pads on Nissan Qashqai J10 – replacement guide

Free download PDF
1.6 MB

How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on Nissan X Trail T30 – replacement guide

Free download PDF
1.26 MB
How to change rear anti roll bar links on Nissan X Trail T30 – replacement guide

Free download PDF
1.2 MB
How to change front anti roll bar links on Nissan Micra K12 – replacement guide

Free download PDF
1.18 MB
How to change front anti roll bar links on NISSAN Kubistar Van (X76) – replacement guide

Free download PDF
1.17 MB
How to change front anti roll bar links on NISSAN PRIMASTAR Box (X83) – replacement guide

Free download PDF
1.37 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

TOP 5 mistakes during DIY oil change | AUTODOC tips

36K views

Published on: 17/06/2021
Top 5 possible reasons your car is shaking or vibrating

6K views

Published on: 14/02/2025
Engine Overheating? Replace Your Cooling Fan to Fix It

6K views

Published on: 15/11/2020
How to Swap an M50 Engine in a BMW E30 Turbo | AUTODOC Project

2K views

Published on: 15/02/2021