Important!
This replacement procedure can be used for:
FIAT BRAVO II (198) 1.6 D Multijet

The steps may slightly vary depending on the car design.

How to replace rear wheel bearing / rear hub bearing on FIAT BRAVO 2 (198) [TUTORIAL AUTODOC]

Required tools:
Required tools:
Wire brush
WD-40 spray
Brake cleaner
All-purpose cleaning spray
Copper grease
Drive socket # 12
Drive socket # 13
Drive socket # 17
Drive socket # 32
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Hammer
Rubber mallet
Crow bar
Wheel chock
AUTODOC recommends:
  • Do not re-use the bearing assembly of your FIAT BRAVO II (198) car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • All work should be done with the engine stopped.
Carry out replacement in the following order:
  1. How to change Wheel Bearing on FIAT BRAVO II (198) 2006 - free PDF and video manuals
    Step 1
    Secure the wheels with chocks.
  2. How to replace FIAT BRAVO II (198) 1.9 D Multijet 2007 Wheel Bearing - step-by-step manuals and video guides
    Step 2
    Loosen the wheel mounting bolts.Use wheel impact socket #17.
  3. FIAT BRAVO II (198) 1.6 D Multijet 2008 Wheel Bearing replacement: free workshop manuals
    Step 3
    Raise the rear of the car and secure on supports.
  4. Changing Wheel Bearing on FIAT BRAVO II (198) 1.4 T-Jet 2009 by yourself
    Step 4
    Unscrew the wheel bolts.
    AUTODOC recommends:
    To avoid injury, hold up the wheel when unscrewing the bolts.
  5. How to remove FIAT BRAVA 1.4 LPG 2010 Wheel Bearing - online easy-to-follow instructions
    Step 5
    Remove the wheel.
  6. How to replace Wheel Bearing on FIAT BRAVO II (198) 2011: download PDF manuals and video instructions
    Step 6
    Clean the brake caliper fasteners. Use a wire brush.Use WD-40 spray.
  7. How hard is it to do yourself: Wheel Bearing replacement on FIAT BRAVO II (198) 1.9 D Multijet 2012 - download illustrated guide
    Step 7
    Unscrew the brake caliper fastening.Use a drive socket #13.Use a ratchet wrench.
  8. Need to know how to renew Wheel Bearing on FIAT BRAVA ? This free workshop manual will help you to do it yourself
    Step 8
    Remove the brake caliper.Use a crowbar.
    AUTODOC recommends:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
  9. Changing of Wheel Bearing on FIAT BRAVO II (198) 2014 won't be an issue if you follow this illustrated step-by-step guide
    Step 9
    Remove the brake pads.
  10. FIAT BRAVA 1.4 Wheel Bearing replacement: online guides and video tutorials
    Step 10
    Clean the brake caliper bracket fasteners. Use a wire brush.Use WD-40 spray.
  11. Replacing Wheel Bearing on FIAT BRAVO II (198) 2016 1.9 D Multijet by yourself
    Step 11
    Unscrew the caliper bracket fastening.Use a drive socket #17.Use a tap wrench.
  12. BRAVO II (198) 1.4 LPG 2017 Wheel Bearing DIY replacement workshop manual
    Step 12
    Remove the caliper bracket.
  13. How to change Wheel Bearing on FIAT BRAVO II (198) 2018 - tips and tricks
    Step 13
    Clean the brake disc fasteners.Use a wire brush.Use WD-40 spray.
  14. Step-by-step recommendations for DIY replacement FIAT BRAVO II (198) 2019 1.4 LPG Wheel Bearing
    Step 14
    Unscrew the brake disc fasteningUse a drive socket #12.Use a ratchet wrench.
  15. DIY replacement of Wheel Bearing on FIAT BRAVO II (198) 1.4 2020 is not an issue anymore with our step-by-step tutorial
    Step 15
    Remove the brake disc.Use a rubber mallet.
  16. How to change Wheel Bearing on FIAT BRAVO II (198) 2006 - free PDF and video manuals
    Step 16
    Remove the hub bearing protection cap.Use a crowbar. Use a hammer.
    AUTODOC recommends:
    Some cars are not equipped with wheel hub caps.
  17. How to replace FIAT BRAVO II (198) 1.9 D Multijet 2007 Wheel Bearing - step-by-step manuals and video guides
    Step 17
    Unscrew the wheel hub axle nut. Use a drive socket #32.Use a tap wrench.
  18. FIAT BRAVO II (198) 1.6 D Multijet 2008 Wheel Bearing replacement: free workshop manuals
    Step 18
    Remove the hub and the bearing together, since they are a sealed unit.
  19. Changing Wheel Bearing on FIAT BRAVO II (198) 1.4 T-Jet 2009 by yourself
    Step 19
    Clean the hub bearing mounting seat.Use all-purpose cleaning spray.
  20. How to remove FIAT BRAVA 1.4 LPG 2010 Wheel Bearing - online easy-to-follow instructions
    Step 20
    Install the new wheel hub with a bearing.
  21. How to replace Wheel Bearing on FIAT BRAVO II (198) 2011: download PDF manuals and video instructions
    Step 21
    Tighten the hub.Use a drive socket #32.Use a torque wrench.Tighten it to 95 Nm torque.
    AUTODOC recommends:
    The wheel bearing unit must not tilt on the axle pin.
  22. How hard is it to do yourself: Wheel Bearing replacement on FIAT BRAVO II (198) 1.9 D Multijet 2012 - download illustrated guide
    Step 22
    Install the hub bearing protection cap.Use a rubber mallet.
  23. Need to know how to renew Wheel Bearing on FIAT BRAVA ? This free workshop manual will help you to do it yourself
    Step 23
    Treat the hub where it contacts the brake disk.Use copper grease.
  24. Changing of Wheel Bearing on FIAT BRAVO II (198) 2014 won't be an issue if you follow this illustrated step-by-step guide
    Step 24
    Install the brake disc.
  25. FIAT BRAVA 1.4 Wheel Bearing replacement: online guides and video tutorials
    Step 25
    Tighten the brake disc fastening.Use a drive socket #12.Use a torque wrench.Tighten it to 10 Nm torque.
  26. Replacing Wheel Bearing on FIAT BRAVO II (198) 2016 1.9 D Multijet by yourself
    Step 26
    Clean the brake caliper bracket from dirt and dust.Use a wire brush.Use a brake cleaner.
    AUTODOC recommends:
    After applying the spray, wait a few minutes.
  27. BRAVO II (198) 1.4 LPG 2017 Wheel Bearing DIY replacement workshop manual
    Step 27
    Install the brake caliper bracket.
  28. How to change Wheel Bearing on FIAT BRAVO II (198) 2018 - tips and tricks
    Step 28
    Tighten the brake caliper bracket.Use a drive socket #17.Use a torque wrench.Tighten it to 85 Nm torque.
  29. Step-by-step recommendations for DIY replacement FIAT BRAVO II (198) 2019 1.4 LPG Wheel Bearing
    Step 29
    Install the brake pads.
  30. DIY replacement of Wheel Bearing on FIAT BRAVO II (198) 1.4 2020 is not an issue anymore with our step-by-step tutorial
    Step 30
    Install the brake caliper and fix it.Use a drive socket #13.Use a torque wrench.Tighten it to 35 Nm torque.
  31. How to change Wheel Bearing on FIAT BRAVO II (198) 2006 - free PDF and video manuals
    Step 31
    Clean the brake disk surface.Use a wire brush.
    Step 32
    Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
  32. How to replace FIAT BRAVO II (198) 1.9 D Multijet 2007 Wheel Bearing - step-by-step manuals and video guides
    Step 33
    Clean the brake disk surface.Use a brake cleaner.
    AUTODOC recommends:
    After applying the spray, wait a few minutes.
  33. FIAT BRAVO II (198) 1.6 D Multijet 2008 Wheel Bearing replacement: free workshop manuals
    Step 34
    Install the wheel.
    AUTODOC recommends:
    To avoid injury, hold up the wheel when screwing in the fastening bolts.
  34. Changing Wheel Bearing on FIAT BRAVO II (198) 1.4 T-Jet 2009 by yourself
    Step 35
    Screw in the wheel bolts.Use wheel impact socket #17.
  35. How to remove FIAT BRAVA 1.4 LPG 2010 Wheel Bearing - online easy-to-follow instructions
    Step 36
    Lower the car and working in a cross order, tighten the wheel bolts.Use a torque wrench.Tighten it to 110 Nm torque.
  36. How to replace Wheel Bearing on FIAT BRAVO II (198) 2011: download PDF manuals and video instructions
    Step 37
    Remove the jacks and chocks.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Vehicle maintenance log book
Know what, when and how to repair, and manage your car expenses
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Google Play AUTODOC Club App
App Store AUTODOC Club App
FIAT BRAVO II (198) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY FIAT BRAVO II (198) Wheel Bearing replacement - online guide
Tips & tricks for your FIAT BRAVO II (198)
View more
  • How to change Hub bearing on FIAT BRAVO II (198) 1.4 - replacement tricks
    How to get rid of minor scratches on the car | AUTODOC
  • Changing Wheel bearing kit FIAT BRAVO II (198) 1.9 D Multijet - Replacement Tips
    How to clean a throttle body yourself | AUTODOC
  • Maintenance Hacks - FIAT BRAVO II (198) 1.6 D Multijet Wheel hub bearing replacement guide
    3 Most Common Reasons for Car Engine Overheating | AUTODOC
  • Replace Axle shaft bearing on FIAT BRAVO II (198) - free video tips
    How to check the quality and density of your antifreeze | AUTODOC