How to change rear brake pads on Fiat Bravo 2 – replacement guide
downloads:
1
Views:
69
0
Users voted – 0
Recommended replacement interval for the part category Brake pad set : 30000km
Important!
This replacement procedure can be used for:
FIAT BRAVO II (198) 2.0 D Multijet (198AXN1B),
FIAT BRAVO II (198) 1.6 D Multijet (198AXL1B),
FIAT BRAVO II (198) 1.4 T-Jet (198AXF1B),
FIAT BRAVO II (198) 1.4 T-Jet (198AXG1B),
FIAT BRAVO II (198) 1.4 (198AXA1B),
FIAT BRAVO II (198) 1.9 D Multijet (198AXC1B),
FIAT BRAVO II (198) 1.9 D Multijet (198AXB1A),
FIAT BRAVO II (198) 1.4 LPG (198AXA1B),
FIAT BRAVO II (198) 1.6 D Multijet (198AXM1B),
FIAT BRAVO II (198) 1.4 16V (198AXS1B)
…
View more
The steps may slightly vary depending on the car design.
How to change rear brake pads / rear brake pad set on FIAT BRAVO 2 (198) [TUTORIAL AUTODOC]
All the parts you need to replace – Brake Pads for BRAVO II (198) and other FIAT models
Replacement: brake pads – Fiat Bravo 2. AUTODOC recommends:
Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
The replacement procedure is identical for all brake pads on the same axle.
All work should be done with the engine stopped.
Replacement: brake pads – Fiat Bravo 2. Recommended sequence of steps:
Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2
Secure the wheels with chocks.
Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 4
Raise the rear of the car and secure on supports.
Step 5
Unscrew the wheel bolts.
Replacement: brake pads – Fiat Bravo 2. Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 6
Remove the wheel.
Step 7
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 8
Unscrew the brake caliper fastening. Use a drive socket #13. Use a ratchet wrench.
Step 9
Remove the brake caliper. Use a crowbar.
AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Step 10
Remove the brake pads.
Replacement: brake pads – Fiat Bravo 2. Professionals recommend:
Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
Step 11
Treat the brake caliper piston. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake pads – Fiat Bravo 2. After applying the spray, wait a few minutes.
Step 12
Press in the brake caliper piston. Use brake caliper wind back tool.
Step 13
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
Replacement: brake pads – Fiat Bravo 2. AUTODOC experts recommend:
After applying the spray, wait a few minutes.
Step 14
Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.
Replacement: brake pads – Fiat Bravo 2. Tip from AUTODOC experts:
Make sure the disc surface is clean before installing the pads.
Step 15
Install new brake pads.
Replacement: brake pads – Fiat Bravo 2. AUTODOC recommends:
Make sure the pads are installed with linings facing the disc.
Step 16
Install the brake caliper and fix it. Use a drive socket #13. Use a torque wrench. Tighten it to 30 Nm torque.
Step 17
Clean the brake disk surface. Use a wire brush.
Step 18
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 19
Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake pads – Fiat Bravo 2. After applying the spray, wait a few minutes.
Step 20
Install the wheel.
Replacement: brake pads – Fiat Bravo 2. AUTODOC experts recommend:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 21
Screw in the wheel bolts. Use wheel impact socket #17.
Step 22
Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 120 Nm torque.
AUTODOC recommends:
Important! Replacement: brake pads – Fiat Bravo 2. Check the brake fluid level in the reservoir and top up if necessary.
Step 23
Tighten the brake fluid reservoir cap. Close the hood.
AUTODOC recommends:
Fiat Bravo 2 – Without starting the engine, press the brake pedal several times until it feels firm.
Step 24
Remove the jacks and chocks.
Replacement: brake pads – Fiat Bravo 2. Professionals recommend:
Slow down smoothly for first 150-200 km after the brake pads replacement. Avoid unneccessary and sharp braking to a stop.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the FIAT Bravo II Hatchback (198) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your FIAT BRAVO II (198)
View more
How to restore wheel rims | AUTODOC tips
How to wash your car in winter | AUTODOC tips
5 common car washing mistakes | AUTODOC tips
How to repair a chipped or cracked windscreen | AUTODOC tips