How to change front brake discs on Renault Scenic 2 – replacement guide
downloads:
2
Views:
40
0
Users voted – 0
Recommended replacement interval for the part category Brake disc : 50000km
Important!
This replacement procedure can be used for:
RENAULT SCÉNIC II (JM0/1_) 1.9 D,
RENAULT SCÉNIC II (JM0/1_) 2.0 (JM05, JM0U, JM1N, JM1U, JM2V),
RENAULT SCÉNIC II (JM0/1_) 2.0 16V Turbo (JM0W),
RENAULT SCÉNIC II (JM0/1_) 1.9 dCi (JM14),
RENAULT SCÉNIC II (JM0/1_) 1.9 dCi (JM15),
RENAULT SCÉNIC II (JM0/1_) 1.5 dCi (JM16),
RENAULT SCÉNIC II (JM0/1_) 1.9 dCi,
RENAULT SCÉNIC II (JM0/1_) 2.0 (JM0S, JM2N),
RENAULT SCÉNIC II (JM0/1_) 1.9 dCi 130,
RENAULT SCÉNIC II (JM0/1_) 1.6 (JM0C, JM0J, JM1B)
…
View more
The steps may slightly vary depending on the car design.
How to change front brake discs / front brake rotors on RENAULT SCENIC 2 (JM) [TUTORIAL AUTODOC]
All the parts you need to replace – Brake Discs for SCÉNIC II (JM0/1_) and other RENAULT models
Replacement: brake discs – Renault Scenic 2. AUTODOC experts recommend:
Replace the brake disks on the car Renault Scenic 2 in complete set for each axis. Regardless of the state of components. This will ensure even braking.
The replacement procedure is identical for both brake disks on the same axle.
When changing the brake discs, always replace the brake pads.
All work should be done with the engine stopped.
Replacement: brake discs – Renault Scenic 2. Use the following procedure:
Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2
Secure the wheels with chocks.
Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 4
Raise the front of the car and secure on supports.
Step 5
Unscrew the wheel bolts.
Replacement: brake discs – Renault Scenic 2. Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 6
Remove the wheel.
Step 7
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 8
Unscrew the brake caliper fastening. Use a drive socket #13. Use a ratchet wrench.
Step 9
Spread the brake pads. Use a crowbar.
Step 10
Remove the brake caliper.
Replacement: brake discs – Renault Scenic 2. AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Step 11
Remove the brake pads. Use a crowbar.
Step 12
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 13
Unscrew the caliper bracket fastening. Use a drive socket #18. Use a tap wrench.
Step 14
Remove the caliper bracket.
Step 15
Clean the brake disk surface. Use a wire brush. Use WD-40 spray.
Step 16
Unscrew the brake disc fastening. Use Torx T30. Use an impact screwdriver.
Replacement: brake discs – Renault Scenic 2. Tip from AUTODOC:
If necessary, use a rubber mallet.
Step 17
Remove the brake disc. Use a rubber mallet.
Step 18
Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 19
Install the brake disc.
Step 20
Tighten the brake disc fastening. Use Torx T30. Use a torque wrench. Tighten it to 15 Nm torque.
Step 21
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use WD-40 spray.
Step 22
Install the brake caliper bracket.
Step 23
Tighten the brake caliper bracket. Use a drive socket #18. Use a torque wrench. Tighten it to 105 Nm torque.
Step 24
Install the brake pads.
Step 25
Treat the brake caliper piston. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake discs – Renault Scenic 2. After applying the spray, wait a few minutes.
Step 26
Press in the brake caliper piston. Use brake caliper wind back tool.
Step 27
Install the brake caliper and fix it. Use a drive socket #13. Use a torque wrench. Tighten it to 32 Nm torque.
Step 28
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 29
Clean the brake disk surface. Use a brake cleaner.
Replacement: brake discs – Renault Scenic 2. Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 30
Install the wheel.
AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. Renault Scenic 2
Step 31
Screw in the wheel bolts. Use wheel impact socket #19.
Step 32
Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 110 Nm torque.
Replacement: brake discs – Renault Scenic 2. AUTODOC experts recommend:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 33
Tighten the brake fluid reservoir cap. Close the hood.
AUTODOC recommends:
Renault Scenic 2 – Press the brake pedal several times with the engine shut down until you feel the resistance built up.
Step 34
Remove the jacks and chocks.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Scénic II (JM) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your RENAULT SCÉNIC II (JM0/1_)
View more
5 car interior cleaning mistakes | AUTODOC tips
DIY car soundproofing | AUTODOC tips
5 Tips for New Drivers | AUTODOC tips
How to reduce fuel consumption | AUTODOC
Most commonly replaced car parts on RENAULT SCÉNIC