
Disclaimer
How to change spark plugs on PEUGEOT 206 SW (2E/K) – replacement guide
downloads:
0
Views:
94

Recommended replacement interval for the part category Spark plug : 60000 km
Important!
This replacement procedure can be used for:
PEUGEOT 206 SW (2E/K) 1.6 16V … View more
The steps may slightly vary depending on the car design.
PEUGEOT 206 SW (2E/K) 1.6 16V … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Spark Plug for 206 SW (2E/K) and other PEUGEOT models
Spark plug
Alternative products

High-temperature anti-seize lubricant
Spark plug socket # 16
Drive socket # 8
Ratchet wrench
Torque wrench
Flat Screwdriver
Telescoping magnet
Fender cover
Replacement: spark plugs – PEUGEOT 206 SW (2E/K). AUTODOC experts recommend:
- The replacement procedure is the same for all spark plugs.
- Warning! Shut down the engine before starting any work – PEUGEOT 206 SW (2E/K).
Carry out replacement in the following order:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Remove the engine cover clips. Use a flat screwdriver.
- Step 4Remove the engine cover. Use a flat screwdriver.Replacement: spark plugs – PEUGEOT 206 SW (2E/K). AUTODOC recommends:Do not apply excessive force when removing the part. Otherwise you may damage it.
- Step 5Detach the connector from the ignition coil. Use a flat screwdriver.
- Step 6Unscrew the ignition coil bolts. Use a drive socket #8. Use a ratchet wrench.
- Step 7Remove the ignition coil by pulling it straight up.
- Step 8Clean dirt, dust and debris from inside the spark plug wells.Step 9Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench.
- Step 10Take out the spark plugs. Use a telescoping magnet.
- Step 11Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new spark plugs.
- Step 12Install the new spark plugs into their mounting seats. Use the spark plug socket #16.
- Step 13Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 25 nm torque.Replacement: spark plugs – PEUGEOT 206 SW (2E/K). Tip from AUTODOC experts:Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the PEUGEOT 206 SW (2E/K) model
Popular maintenance tutorials for Peugeot 206 SW
Complete guides for changing the Engine spark plug on different PEUGEOT 206 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your PEUGEOT 206 SW (2E/K)
View more
- 5 mistakes when replacing consumables
- The most common problems when buying a used car | AUTODOC
- Prevent Engine Damage: How to Identify Rocker Cover Gasket Issues and Proper Replacement | AUTODOC
- Reviving Your Car: How to Start After Extended Idle Time | AUTODOC Tips
Most commonly replaced car parts on PEUGEOT 206
Time to replace parts? Get even better deals in our Shop app.

SCAN ME