How to carry out replacement: Wheel Bearing 1.3 i-V TEC City GM
Disclaimer
Change City GM 1.3 i-V TEC Wheel Bearing yourself – manuals and video tutorials

How to change rear wheel bearing on HONDA City Saloon (GM2, GM3) – replacement guide

downloads: 9
Views: 147
Download your free tutorial and fix HONDA CITY Saloon (GM) 1.5 Flex problems yourself Download for free 2.26 MB Wheel Bearing for City GM Shop now
Leave a comment Open in a new tab
Important!
This replacement procedure can be used for:
HONDA CITY Saloon (GM) 1.3 i-V TEC … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for CITY Saloon (GM) and other HONDA models
Alternative products
How to change Wheel bearing kit on City GM 1.3 i-V TEC – step-by-step instructions for straightforward car repair Wheel bearing kit
Tools
Replacement: wheel bearing – HONDA CITY Saloon (GM). Tools you'll need:
Wire brush
WD-40 spray
All-purpose cleaning spray
Brake cleaner
Copper grease
Combination spanner #12
Combination spanner #17
Drive socket # 12
Drive socket # 14
Drive socket # 17
Drive socket # 32
Wheel impact socket #19
Brake caliper wind back tool
Ratchet wrench
Torque wrench
Impact screwdriver
Phillips screwdriver
Flat chisel
Tap wrench
Hammer
Rubber mallet
Crow bar
Wheel chock
Buy tools
Replacement: wheel bearing – HONDA CITY Saloon (GM). AUTODOC recommends:
  • Do not re-use the bearing assembly of your HONDA CITY Saloon (GM) car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • Please note: all work on the car – HONDA CITY Saloon (GM) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    Open the bonnet. Unscrew the brake fluid reservoir cap.
    Step 2
    How to change Wheel Bearing on City GM 2008 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 3
    How to replace HONDA CITY Saloon (GM) 1.3 i-V TEC 2009 Wheel Bearing - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #19.
  3. Step 4
    Raise the rear of the car and secure on supports.
    Step 5
    City GM 1.5 i-VTEC 2010 Wheel Bearing replacement: free workshop manuals
    Unscrew the wheel bolts.
    Replacement: wheel bearing – HONDA CITY Saloon (GM). Tip:
    To avoid injury, hold up the wheel when unscrewing the bolts.
  4. Step 6
    Changing Wheel Bearing on HONDA CITY Saloon (GM) 1.5 Flex 2011 by yourself
    Remove the wheel.
  5. Step 7
    How to remove HONDA CITY 1.3 i-V TEC 2012 Wheel Bearing - online easy-to-follow instructions
    Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
  6. Step 8
    How to replace Wheel Bearing on HONDA CITY Saloon (GM) 2013: download PDF manuals and video instructions
    Detach the parking brake cable from the bracket on the brake caliper. Use a drive socket #17. Use a ratchet wrench. Use a crowbar.
  7. Step 9
    How hard is it to do yourself: Wheel Bearing replacement on City GM 1.5 i-VTEC (GM2) 2014 - download illustrated guide
    Unscrew the brake caliper fastening. Use a combination spanner #12. Use a combination spanner #17.
  8. Step 10
    Need to know how to renew Wheel Bearing on HONDA CITY 2015? This free workshop manual will help you to do it yourself
    Remove the brake caliper.
    Replacement: wheel bearing – HONDA CITY Saloon (GM). AUTODOC experts recommend:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
  9. Step 11
    Changing of Wheel Bearing on City GM 2016 won't be an issue if you follow this illustrated step-by-step guide
    Remove the brake pads.
  10. Step 12
    HONDA CITY 1.3 i-V TEC Wheel Bearing replacement: online guides and video tutorials
    Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
  11. Step 13
    Replacing Wheel Bearing on City GM 2018 1.3 i-V TEC by yourself
    Unscrew the caliper bracket fastening. Use a drive socket #14. Use a ratchet wrench.
  12. Step 14
    CITY Saloon (GM) 1.3 i-V TEC 2019 Wheel Bearing DIY replacement workshop manual
    Remove the caliper bracket.
  13. Step 15
    How to change Wheel Bearing on HONDA CITY Saloon (GM) 2020 - tips and tricks
    Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
  14. Step 16
    Step-by-step recommendations for DIY replacement City GM 2021 1.3 i-V TEC Wheel Bearing
    Unscrew the brake disc fastening. Use a Phillips screwdriver. Use an impact screwdriver.
  15. Step 17
    DIY replacement of Wheel Bearing on HONDA CITY Saloon (GM) 1.5 i-VTEC (GM2) 2022 is not an issue anymore with our step-by-step tutorial
    Remove the brake disc.
  16. Step 18
    How to change Wheel Bearing on City GM 2008 - free PDF and video manuals
    Remove the hub bearing protection cap. Use a hammer. Use a crowbar.
    AUTODOC recommends:
    Some cars are not equipped with wheel hub caps.
  17. Step 19
    How to replace HONDA CITY Saloon (GM) 1.3 i-V TEC 2009 Wheel Bearing - step-by-step manuals and video guides
    Unstake the wheel hub retaining nut. Use a flat metal-working chisel. Use a hammer.
  18. Step 20
    City GM 1.5 i-VTEC 2010 Wheel Bearing replacement: free workshop manuals
    Unscrew the wheel hub axle nut. Use a drive socket #32. Use a tap wrench.
  19. Step 21
    Changing Wheel Bearing on HONDA CITY Saloon (GM) 1.5 Flex 2011 by yourself
    Remove the hub and the bearing together, since they are a sealed unit.
  20. Step 22
    How to remove HONDA CITY 1.3 i-V TEC 2012 Wheel Bearing - online easy-to-follow instructions
    Clean the hub bearing mounting seat. Use all-purpose cleaning spray.
  21. Step 23
    How to replace Wheel Bearing on HONDA CITY Saloon (GM) 2013: download PDF manuals and video instructions
    Install the new wheel hub with a bearing.
  22. Step 24
    How hard is it to do yourself: Wheel Bearing replacement on City GM 1.5 i-VTEC (GM2) 2014 - download illustrated guide
    Tighten the hub. Use a drive socket #32. Use a torque wrench. Tighten it to 181 Nm torque.
    Replacement: wheel bearing – HONDA CITY Saloon (GM). Tip from AUTODOC:
    The wheel bearing unit must not tilt on the axle pin.
  23. Step 25
    Need to know how to renew Wheel Bearing on HONDA CITY 2015? This free workshop manual will help you to do it yourself
    Restake the wheel hub retaining nut. Use a flat metal-working chisel. Use a hammer.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?

Find out which tyre and wheel sizes are compatible with the HONDA City Saloon (GM2, GM3) model

City GM tyre size

Popular maintenance tutorials for City GM

More manuals for City GM

Complete guides for changing the Wheel bearings on different HONDA CITY models

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY HONDA CITY Saloon (GM) Wheel Bearing replacement - online guide
Tips & tricks for your HONDA CITY Saloon (GM)
View more
  • How to change Wheel bearings on HONDA CITY Saloon (GM) 1.5 i-VTEC (GM2) - replacement tricks
    How to easily repair a punctured tyre | AUTODOC tips
    3K views
    Published on: 25/02/2021
  • Changing Hub bearing City GM 1.3 i-V TEC - Replacement Tips
    Top 5 Mistakes to Avoid for Safe Engine Bay Repairs | AUTODOC Tips
    8K views
    Published on: 04/08/2023
  • Maintenance Hacks - HONDA CITY Saloon (GM) 1.5 i-VTEC Wheel bearing kit replacement guide
    How to Fix P0401 ✅ error code Insufficient EGR flow
    4K views
    Published on: 08/05/2025
  • Replace Wheel hub bearing on City GM - free video tips
    What causes engine misfire? | AUTODOC
    6K views
    Published on: 10/07/2020

Most commonly replaced car parts on HONDA CITY

Professional manuals for the most common HONDA models

Autodoc CLUB App icon
Time to replace parts? Get even better deals in our Shop app.
HONDA CITY Saloon (GM) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
SCAN ME