Important!

This replacement procedure can be used for:
HONDA Jazz Saloon (GD_) 1.3 (GD6), HONDA Jazz Saloon (GD_) 1.5 i-DSI (GD8), HONDA Jazz Saloon (GD_) 1.5 i-DSI 4WD (GD9), HONDA Jazz Saloon (GD_) 1.5 i-DSI 4WD (GD9) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for Jazz Saloon (GD_) and other HONDA models

Wheel bearing kit

        Wheel bearing kit for Jazz Saloon (GD) Petrol (86 hp)
      
        Wheel bearing kit for Jazz Saloon (GD) Petrol (110 hp)
      
        Wheel bearing kit for Jazz Saloon (GD) Petrol (110 hp)
      
        Wheel bearing kit for Jazz Saloon (GD) Petrol (90 hp)

Replacement: wheel bearing – HONDA JAZZ Saloon. Tools you need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        High-temperature ceramic grease
                      
                        Combination spanner #17
                      
                        Combination spanner #19
                      
                        Drive socket # 10 
                      
                        Drive socket # 17 
                      
                        Drive socket # 32 
                      
                        Wheel impact socket #19
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Bush and bearing driver set
                      
                        Phillips Screwdriver
                      
                        Flat Screwdriver
                      
                        Hammer
                      
                        Flat chisel
                      
                        Crow bar
                      
                        Rubber mallet
                      
                        Round-nose pliers
                      
                        Nippers
                      
                        Ball joint puller
                      
                        Wheel chock

Buy tools

Replacement: wheel bearing – HONDA JAZZ Saloon. AUTODOC experts recommend:

The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
Do not re-use the bearing assembly of your HONDA JAZZ Saloon car.
All work should be done with the engine stopped.

Replacement: wheel bearing – HONDA JAZZ Saloon. Recommended sequence of steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: wheel bearing – HONDA JAZZ Saloon. AUTODOC experts recommend:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Unstake the wheel hub retaining nut. Use a flat metal-working chisel. Use a hammer.

Step 7

Clean the wheel hub fastener. Use a wire brush. Use WD-40 spray.

Step 8

Unscrew the wheel hub axle nut. Use a drive socket #32. Use a ratchet wrench.
Step 9

Remove the fastening nut.

Step 10

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.

Step 11

Unscrew the caliper bracket fastening. Use a drive socket #17. Use a ratchet wrench.
Step 12

Remove the fastening bolts (2 pieces).

Step 13

Remove the brake caliper together with its bracket.

AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 14

Clean the brake disc fastener. Use a wire brush. Use WD-40 spray.

Step 15

Unscrew the brake disc fastening. Use a Phillips screwdriver.
Step 16

Remove the brake disc.
Step 17

Remove the cotter pin. Use nippers.
Step 18

Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 19

Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
Step 20

Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
Step 21

Clean the fastener that connects the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 22

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #19.
Step 23

Disconnect the lower arm from the steering knuckle. Use a crowbar. Use a rubber mallet.
Step 24

Detach the driveshaft from the steering knuckle.
Step 25.1

Remove the ABS sensor from the steering knuckle. Use a drive socket #10. Use a ratchet wrench.

Step 25.2

Use round-nose pliers.
Step 26

Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 27

Unscrew the fasteners connecting the suspension strut to the steering knuckle. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 28

Remove the fastening bolts.

Step 29

Disconnect the steering knuckle from the shock absorber strut.
Step 30

Remove the steering knuckle together with the hub.
Step 31

Remove the wheel hub from the steering knuckle. Use a bush and bearing driver set. Use a hammer.
Step 32

Remove the wheel hub bearing retaining ring. Use round-nose pliers. Use a flat screwdriver.
Step 33

Press out the wheel hub bearing. Use a bush and bearing driver set.
Step 34

Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
Step 35

Press the new bearing in the steering knuckle. Use a bush and bearing driver set.

Replacement: wheel bearing – HONDA JAZZ Saloon. Tip from AUTODOC:
Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
Step 36

Install the retaining ring on the steering knuckle. Use round-nose pliers.
Step 37

Install the wheel hub on the steering knuckle. Use a bush and bearing driver set.
Step 38

Treat the shock strut mounting seat on the steering knuckle. Use a wire brush. Use WD-40 spray.

Step 39

Install the steering knuckle with a hub in assembly.

Step 40

Fix the shock absorber strut on the steering knuckle.
Step 41

Install the fastening bolts.
Step 42

Treat the splines of the driveshaft CV joint. Use a wire brush. Use WD-40 spray.
Step 43

Install the steering knuckle on the CV axle.
Step 44

Connect the lower control arm to the steering knuckle. Use a crowbar.
Step 45

Tighten the fastener connecting the ball joint to the steering knuckle. Use a combination spanner #19. Use a torque wrench. Tighten it to 59 Nm torque.
Step 46

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a combination spanner #17. Use a drive socket #17. Use a torque wrench. Tighten it to 69 Nm torque.
Step 47

Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 48

Install the brake disc.
Step 49

Tighten the brake disc fastening. Use a Phillips screwdriver. Use a torque wrench. Tighten it to 10 Nm torque.
Step 50

Clean the mounting seats of the caliper and its bracket. Use a wire brush. Use WD-40 spray.

Step 51

Install the brake caliper together with its bracket.
Step 52

Install the fastening bolts (2 pieces).

Step 53

Tighten the brake caliper bracket. Use a drive socket #17. Use a torque wrench. Tighten it to 108 Nm torque.
Step 54

Install the fastening nut.

Step 55

Tighten the hub. Use a drive socket #32. Use a torque wrench. Tighten it to 181 Nm torque.
Step 56

Restake the wheel hub retaining nut. Use a flat metal-working chisel. Use a hammer.
Step 57

Install the ABS sensor on the steering knuckle and secure it. Use a drive socket #10. Use a ratchet wrench.
Step 58

Connect the tie rod end to the steering knuckle.
Step 59

Tighten the fastening nut connecting the tie rod end to the steering knuckle. Use a drive socket #17. Use a torque wrench. Tighten it to 43 nm torque.
Step 60

Install the cotter pin. Use nippers.
Step 61

Treat the fastener connecting the tie rod end to the steering knuckle. Treat the fasteners of the ball joint. Treat the shock strut fasteners. Use copper grease.
Step 62

Treat the surface where the brake disc contacts the wheel rim. Use high-temperature ceramic grease.
Step 63

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – HONDA JAZZ Saloon. After applying the spray, wait a few minutes.
Step 64

Install the wheel.

Replacement: wheel bearing – HONDA JAZZ Saloon. Tip:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 65

Screw in the wheel bolts. Use wheel impact socket #19.
Step 66

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 108 nm torque.
Step 67

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the HONDA Jazz Saloon (GD) model.

Browse tyres

How to change track rod end on HONDA Jazz Saloon (GD) – replacement guide

Free download PDF
2.37 MB
How to change rear windshield wipers on HONDA Jazz Saloon (GD) – replacement guide

Free download PDF
1.41 MB
How to change pollen filter on HONDA Jazz Saloon (GD_) – replacement guide

Free download PDF
849.92 KB
How to replace rear brake pads of disc brake on Honda CR-V III

Free download PDF
1.18 MB
How to replace the front brake pads of disc brake on Honda CR-V III

Free download PDF
1.26 MB
How to replace the rear brake disc on Honda CR-V III

Free download PDF
1.33 MB

How to change front wheel bearing on HONDA City Saloon (GE4) – replacement guide

Free download PDF
3.89 MB
How to change rear wheel bearing on HONDA City Saloon (GE4) – replacement guide

Free download PDF
1.78 MB
How to change rear wheel bearing on HONDA City Saloon (GM2, GM3) – replacement guide

Free download PDF
2.26 MB
How to change wheel bearing on a car – replacement tutorial

Universal

Free download PDF
2.41 MB
How to change front wheel bearing on Honda Jazz GD – replacement guide

Free download PDF
3.68 MB
How to change rear wheel bearing on Honda Insight ZE2_ZE3 – replacement guide

Free download PDF
2.19 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Replacing your engine cooling fan | AUTODOC tips

2K views

Published on: 15/11/2020
What to do if your check engine light is on | AUTODOC tips

15K views

Published on: 19/08/2020
How to fix your car with AUTODOC CLUB

16K views

Published on: 30/11/2021
How to unlock your car without a key | AUTODOC tips

842K views

Published on: 15/09/2022