Disclaimer
How to change front suspension strut on FORD Focus C-Max (DM2) – replacement guide
downloads:
1
Views:
25
Important!
This replacement procedure can be used for:
FORD Focus C-Max (DM2) 1.6 Ti, FORD Focus C-Max (DM2) 1.6 … View more
The steps may slightly vary depending on the car design.
FORD Focus C-Max (DM2) 1.6 Ti, FORD Focus C-Max (DM2) 1.6 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Shock Absorber for Focus C-Max (DM2) and other FORD models
Alternative products

Wire brush
WD-40 spray
Copper grease
Drive socket # 13
Drive socket # 15
Drive socket # 18
Torx bit T40
Torx bit T30
HEX bit No.H6.
Shock absorber socket
Wheel impact socket #19
Combination spanner #19
Ratchet wrench
Torque wrench
Tap wrench
Hammer
Flat chisel
Crow bar
Hydraulic transmission jack
Hydraulic strut spring compressor
Fender cover
Wheel chock
Replacement: suspension strut – FORD FOCUS C-MAX. AUTODOC experts recommend:
- Both shock struts of the front suspension should be replaced simultaneously.
- The replacement procedure is identical for the left and right shock struts of the front suspension.
- All work should be done with the engine stopped.
Replacement: suspension strut – FORD FOCUS C-MAX. Recommended sequence of steps:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Remove the windscreen wiper arm nut covers. - Step 4
Unscrew the fasteners of the windscreen wiper arms. Use a drive socket #15. Use a ratchet wrench. - Step 5
Clean the pivots of the windscreen wiper arms. Use WD-40 spray. - Step 6
Remove the wiper arms. - Step 7
Remove the clips of the plastic cowl grille. Use a crowbar. - Step 8
Raise the wiper plastic cowl grille. - Step 9
Unscrew the fastener of the lower wiper plastic cowl grille. Use Torx T30. Use a ratchet wrench. - Step 10
Remove the lower wiper plastic cowl grille. - Step 11
Loosen the upper fastener of the shock strut mount. Use a drive socket #13. Use a ratchet wrench. - Step 12
Secure the wheels with chocks. - Step 13
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 14Raise the front of the car and secure on supports.Step 15
Unscrew the wheel bolts.Replacement: suspension strut – FORD FOCUS C-MAX. AUTODOC recommends:To avoid injury, hold up the wheel when unscrewing the bolts. - Step 16
Remove the wheel. - Step 17
Disconnect the wiring and the brake hose from the bracket on the shock strut. - Step 18
Clean the fasteners connecting the stabiliser link to the shock strut, and those connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray. - Step 19
Unscrew the nut and remove the stabilizer rod from the shock strut. Use a drive socket #15. Use a ratchet wrench. - Step 20
Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #18. Use a ratchet wrench. Use a tap wrench. - Step 21
Prop up the steering knuckle. Use a hydraulic transmission jack. - Step 22
Release the lower fastener connecting the shock strut to the steering knuckle. Use a special drive socket to remove the shock absorber. Use a hammer. Use a flat metal-working chisel. - Step 23
Disconnect the steering knuckle from the shock absorber strut. Use a crowbar. - Step 24
Unscrew the upper fastening of the shock absorber strut.AUTODOC recommends:Important! Hold the suspension strut while unscrewing the fastening bolts. FORD FOCUS C-MAX - Step 25
Lower the hydraulic transmission jack by 10-15 cm.Replacement: suspension strut – FORD FOCUS C-MAX. Tip:Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms. - Step 26
Remove the suspension strut. - Step 27
Set the shock absorber strut on the spring compressor tool.Replacement: suspension strut – FORD FOCUS C-MAX. Tip from AUTODOC experts:Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles. - Step 28
Compress the spring. - Step 29
Remove the strut piston rod nut. Use Torx T40. Use a combination spanner #19. Use a ratchet wrench. - Step 30
Remove the top strut mount. Use a crowbar. - Step 31
Release the coil spring. - Step 32
Remove the spring. - Step 33
Remove the old shock absorber from the hydraulic coil spring compressor.Replacement: suspension strut – FORD FOCUS C-MAX. Professionals recommend:Τhoroughly examine the shock absorber mount, dust boot, bump stop. Replace them if necessary.Before installing a new shock absorber you should pump it manually 3-5 times. - Step 34
Install the new shock absorber on the hydraulic coil spring compressor. - Step 35
Install the dust sleeve and the bump stop on the new shock absorber. - Step 36
Install the spring on the shock absorber. - Step 37
Compress the spring. - Step 38
Install the upper strut mount and the strut mount bearing.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the FORD Focus C-Max (DM2) model
Popular maintenance tutorials for Focus C-Max (DM2)
Complete guides for changing the Shock absorbers on different FORD FOCUS models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your FORD Focus C-Max (DM2)
View more
Drive with Care: 8 Common Bad Driving Habits Explained | AUTODOC
How to Safely Wash Your Car in Winter Without Damage | AUTODOC tips
Discover the 4 Key Reasons Your CHECK ENGINE Light Could Be On | AUTODOC Tips
Easy Steps to Fix Minor Scratches on Your Vehicle | AUTODOC tips
Most commonly replaced car parts on FORD FOCUS
Time to replace parts? Get even better deals in our Shop app.

SCAN ME








































