Important!

This replacement procedure can be used for:
FIAT PUNTO EVO (199) 1.4 Natural Power, FIAT PUNTO EVO (199) 1.3 D Multijet, FIAT PUNTO EVO (199) 1.2, FIAT PUNTO EVO (199) 1.4 (199AXH1A), FIAT PUNTO EVO (199) 1.3 D Multijet, FIAT PUNTO EVO (199) 1.4 LPG, FIAT PUNTO EVO (199) 1.2, FIAT PUNTO EVO (199) 1.4 (199AXB1A), FIAT PUNTO EVO (199) 1.4 16V, FIAT PUNTO EVO (199) 1.4 16V (199AXW1A), FIAT PUNTO EVO (199) 1.3 D Multijet (199AXC1A, 199BXC1A, 199AXT1A, 199BXT1A), FIAT PUNTO EVO (199) 1.3 D Multijet, FIAT PUNTO EVO (199) 1.6 D Multijet, FIAT PUNTO EVO (199) 1.3 D Multijet (199AXD1B, 199AXD1A, 199BXD1B, 199BXD1A,... … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Suspension arm

Replacement: front lower arm – FIAT PUNTO EVO (199). Tools you might need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner
                    
                      Copper grease
                    
                      Combination spanner #16
                    
                      Combination spanner #18
                    
                      Drive socket # 16
                    
                      Drive socket # E18
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Flat chisel
                    
                      Hammer
                    
                      Tap wrench
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: front lower arm – FIAT PUNTO EVO (199). AUTODOC recommends:

The replacement procedure is identical for the left and right lower control arms.
All work should be done with the engine stopped.

Replacement: front lower arm – FIAT PUNTO EVO (199). Take the following steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. FIAT PUNTO EVO (199)
Step 5

Remove the wheel.
Step 6

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.

Replacement: front lower arm – FIAT PUNTO EVO (199). Tip:
After applying the spray, wait a few minutes.Wear protective goggles.
Step 7

Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #16. Use a drive socket #16. Use a tap wrench.
Step 8

Remove the fastening bolt.
Step 9

Unscrew the front arm fastener. Use a drive socket #E18. Use a tap wrench.
Step 10

Unscrew the rear fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #E18. Use a tap wrench.
Step 11

Remove the fastening bolts. Use a drive socket #E18. Use a ratchet wrench.
Step 12

Release the fastener connecting the ball joint to the steering knuckle. Use a flat metal-working chisel. Use a hammer.
Step 13

Disconnect the ball joint from the steering knuckle.
Step 14

Remove the arm.
Step 15

Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
Step 16

Install a new arm.

Replacement: front lower arm – FIAT PUNTO EVO (199). AUTODOC experts recommend:
During the installation process, use only new bolts and nuts.Do not damage the ball joint cover.
Step 17

Install the fastening bolts. Use a combination spanner #18. Use a drive socket #E18. Use a tap wrench.
Step 18

Screw the rear fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #E18. Use a ratchet wrench.
Step 19

Support the arm. Use a hydraulic transmission jack.
Step 20

Connect the ball joint to the steering knuckle.
Step 21

Install the fastening bolt.
Step 22

Screw the fasteners of the ball joint. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
Step 23

Screw the rear fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #E18. Use a ratchet wrench.
Step 24

Tighten the front fastener connecting the control arm to the subframe. Use a drive socket #E18. Use a torque wrench. Tighten it to 60 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 25

Tighten the rear fastener connecting the arm to the body subframe. Use a drive socket #E18. Use a torque wrench. Tighten it to 60 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 26

Tighten the ball joint fastener. Use a drive socket #16. Use a torque wrench. Tighten it to 50 nm torque.
Step 27

Remove the support from under the arm.

AUTODOC recommends:
Replacement: front lower arm – FIAT PUNTO EVO (199). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 28

Treat all joints of the arm. Use copper grease.
Step 29

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 30

Clean the brake disk surface. Use a brake cleaner.

Replacement: front lower arm – FIAT PUNTO EVO (199). Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 31

Install the wheel.

Replacement: front lower arm – FIAT PUNTO EVO (199). Professionals recommend:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 32

Screw in the wheel bolts. Use wheel impact socket #17.
Step 33

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 nm torque.
Step 34

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the FIAT Punto Evo Hatchback (199) model

Fiat Punto Evo tyre size

How to change track rod end on FIAT PUNTO EVO (199) – replacement guide

Free download PDF
1.49 MB
How to change front anti roll bar links on FIAT PUNTO EVO (199) – replacement guide

Free download PDF
1.3 MB
How to change front brake pads on FIAT PUNTO EVO (199) – replacement guide

Free download PDF
1.61 MB
How to change front brake discs on FIAT PUNTO EVO (199) – replacement guide

Free download PDF
2.01 MB
How to change serpentine belt on FIAT Punto Evo Hatchback (199) – replacement guide

Free download PDF
1.39 MB
How to change spark plugs on FIAT PUNTO EVO (199) – replacement guide

Free download PDF
1.37 MB

How to change front lower arm on Fiat Punto 188 – replacement guide

Free download PDF
2.03 MB
How to change front lower arm on FIAT PUNTO (199) – replacement guide

Free download PDF
2 MB
How to change front lower arm on FIAT Punto Evo Van (199) – replacement guide

Free download PDF
2.11 MB
How to change control arm on a car – replacement tutorial

Universal

Free download PDF
1.07 MB
How to change front lower arm on Fiat Panda 169 – replacement guide

Free download PDF
1.96 MB
How to change front lower arm on Fiat Punto 199 – replacement guide

Free download PDF
2.07 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to Polish Your Car Yourself and Save Money on Garage Services | AUTODOC tips

6K views

Published on: 31/03/2022
How to repair a bumper yourself | AUTODOC tips

19K views

Published on: 01/06/2023
Stop Rust Before It Starts: Top 5 Tips for Car Body Protection | AUTODOC Insights

7K views

Published on: 27/07/2023
Kolbenschmidt plastic gauge overview

3K views

Published on: 23/04/2025