Disclaimer
How to change front lower arm on FIAT Punto Evo Van (199) – replacement guide
downloads:
0
Views:
12
Important!
This replacement procedure can be used for:
FIAT PUNTO EVO Van (199_) 1.4 (199.AXB1A) … View more
The steps may slightly vary depending on the car design.
FIAT PUNTO EVO Van (199_) 1.4 (199.AXB1A) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Control Arm for PUNTO EVO Van (199_) and other FIAT models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #16
Combination spanner #18
Drive socket # 16
Drive socket # E18
Wheel impact socket #17
Ratchet wrench
Torque wrench
Flat chisel
Hammer
Tap wrench
Hydraulic transmission jack
Wheel chock
Replacement: front lower arm – FIAT PUNTO EVO Van (199_). AUTODOC recommends:
- The replacement procedure is identical for the left and right lower control arms.
- All work should be done with the engine stopped.
Replacement: front lower arm – FIAT PUNTO EVO Van (199_). Take the following steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. FIAT PUNTO EVO Van (199_) - Step 5
Remove the wheel. - Step 6
Clean all joints of the arm. Use a wire brush. Use WD-40 spray.Replacement: front lower arm – FIAT PUNTO EVO Van (199_). Tip:After applying the spray, wait a few minutes.Wear protective goggles. - Step 7
Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #16. Use a drive socket #16. Use a tap wrench. - Step 8
Remove the fastening bolt. - Step 9
Unscrew the front arm fastener. Use a drive socket #E18. Use a tap wrench. - Step 10
Unscrew the rear fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #E18. Use a tap wrench. - Step 11
Remove the fastening bolts. Use a drive socket #E18. Use a ratchet wrench. - Step 12
Release the fastener connecting the ball joint to the steering knuckle. Use a flat metal-working chisel. Use a hammer. - Step 13
Disconnect the ball joint from the steering knuckle. - Step 14
Remove the arm. - Step 15
Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray. - Step 16
Install a new arm.Replacement: front lower arm – FIAT PUNTO EVO Van (199_). AUTODOC experts recommend:During the installation process, use only new bolts and nuts.Do not damage the ball joint cover. - Step 17
Install the fastening bolts. Use a combination spanner #18. Use a drive socket #E18. Use a tap wrench. - Step 18
Screw the rear fastener connecting the control arm to the subframe. Use a combination spanner #18. Use a drive socket #E18. Use a ratchet wrench. - Step 19
Support the arm. Use a hydraulic transmission jack. - Step 20
Connect the ball joint to the steering knuckle.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the FIAT Punto Evo Van (199) model
Popular maintenance tutorials for FIAT PUNTO EVO Van (199_)
Complete guides for changing the Control arm on different FIAT PUNTO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your FIAT PUNTO EVO Van (199_)
View more
Top 5 mistakes when replacing spark plugs | AUTODOC tips
How to Swap an M50 Engine in a BMW E30 Turbo | AUTODOC Project
Top 4 Car Cleaning Products to Protect Your Car's Body | AUTODOC Tips
Prevent Engine Damage: How to Identify Rocker Cover Gasket Issues and Proper Replacement | AUTODOC
Most commonly replaced car parts on FIAT PUNTO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME






























