How to change front brake pads on Suzuki Swift MK3 – replacement guide
downloads:
20
Views:
590
5
Users voted – 2
Recommended replacement interval for the part category Brake pad set : 30000km
Important!
This replacement procedure can be used for:
SUZUKI SWIFT III (MZ, EZ) 1.5 4x4 (RS 415, ZD21S),
SUZUKI SWIFT III (MZ, EZ) 1.3 (RS 413, ZC11S),
SUZUKI SWIFT III (MZ, EZ) 1.3 DDiS (RS 413D),
SUZUKI SWIFT III (MZ, EZ) 1.3 4x4 (RS 413, ZD11S),
SUZUKI SWIFT III (MZ, EZ) 1.6 (RS 416, RR 416, ZC31S),
SUZUKI SWIFT III (MZ, EZ) 1.3 4x4 (RS 413, ZD11S),
SUZUKI SWIFT III (MZ, EZ) 1.3 DDiS (RS 413D)
…
View more
The steps may slightly vary depending on the car design.
How to change front brake discs and front brake pads set on SUZUKI SWIFT 3 [TUTORIAL AUTODOC]
All the parts you need to replace – Brake Pads for SWIFT III (MZ, EZ) and other SUZUKI models
Replacement: brake pads – Suzuki Swift MK3. AUTODOC experts recommend:
Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
The replacement procedure is identical for all brake pads on the same axle.
Please note: all work on the car – Suzuki Swift MK3 – should be done with the engine switched off.
Carry out replacement in the following order:
Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2
Secure the wheels with chocks.
Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #21.
Step 4
Raise the front of the car and secure on supports.
Step 5
Unscrew the wheel bolts.
AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. Suzuki Swift MK3
Step 6
Remove the wheel.
Step 7
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 8
Unscrew the brake caliper fastening. Use a combination spanner #15. Use a drive socket #13. Use a ratchet wrench.
Step 9
Spread the brake pads. Use a crowbar.
Step 10
Remove the brake caliper.
Replacement: brake pads – Suzuki Swift MK3. Tip:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 11
Remove the brake pads.
Replacement: brake pads – Suzuki Swift MK3. AUTODOC experts recommend:
Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
Step 12
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake pads – Suzuki Swift MK3. After applying the spray, wait a few minutes.
Step 13
Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.
Replacement: brake pads – Suzuki Swift MK3. Professionals recommend:
Make sure the disc surface is clean before installing the pads.
Step 14
Install new brake pads.
Replacement: brake pads – Suzuki Swift MK3. AUTODOC recommends:
Make sure the pads are installed with linings facing the disc.
Step 15
Treat the brake caliper piston. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake pads – Suzuki Swift MK3. After applying the spray, wait a few minutes.
Step 16
Press in the brake caliper piston. Use brake caliper wind back tool.
Step 17.1
Install the brake caliper and fix it.
Step 17.2
Use a combination spanner #15. Use a drive socket #13. Use a torque wrench. Tighten it to 35 Nm torque.
Step 18
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 19
Clean the brake disk surface. Use a brake cleaner.
Replacement: brake pads – Suzuki Swift MK3. Professionals recommend:
After applying the spray, wait a few minutes.
Step 20
Install the wheel.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Suzuki Swift MK3
Step 21
Screw in the wheel bolts. Use wheel impact socket #21.
Step 22
Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #21. Use a torque wrench. Tighten it to 85 nm torque.
Step 23
Remove the jacks and chocks.
Replacement: brake pads – Suzuki Swift MK3. Tip:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 24
Tighten the brake fluid reservoir cap. Close the hood.
Replacement: brake pads – Suzuki Swift MK3. AUTODOC experts recommend:
Without starting the engine, press the brake pedal several times until you feel significant resistance.Slow down smoothly for first 150-200 km after the brake pads replacement. Avoid unneccessary and sharp braking to a stop.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 2
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the SUZUKI Swift III Hatchback (MZ, EZ) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your SUZUKI SWIFT III (MZ, EZ)
View more
DIY alternator repair | AUTODOC tips
How to restore a steering wheel | AUTODOC tips
BMW E30 Turbo Suspension Swap: Boost Your Handling | AUTODOC project
#DIY Tips for Fixing Your Car's Air Conditioning Issues | Don't Wait for Costly Repairs!