Important!

This replacement procedure can be used for:
PEUGEOT 407 (6D_) 1.6 HDi 110, PEUGEOT 407 SW (6E_) 1.6 HDi 110

The steps may slightly vary depending on the car design.

How to change front anti roll bar link on PEUGEOT 407 Saloon [TUTORIAL AUTODOC]

Replacement: anti roll bar links – Peugeot 407 saloon. List of the tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Copper grease 
                      
                        Brake cleaner
                      
                        Combination spanner #18
                      
                        Combination spanner #24
                      
                        Torx bit T40
                      
                        HEX bit no.H6.
                      
                        Wheel impact socket #19
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Pin punch
                      
                        Hammer
                      
                        Crow bar
                      
                        Wheel chock

All the parts you need to replace – Anti Roll Bar Links for 407 (6D_) and other PEUGEOT models

PEUGEOT 407 (6D_) 1.6 HDi 110

PEUGEOT 407 SW (6E_) 1.6 HDi 110

PEUGEOT 407 (6D_) 1.6 HDi 110

PEUGEOT 407 SW (6E_) 1.6 HDi 110

PEUGEOT 407 (6D_) 1.6 HDi 110

PEUGEOT 407 SW (6E_) 1.6 HDi 110

Replacement: anti roll bar links – Peugeot 407 saloon. AUTODOC experts recommend:

Replace the stabiliser links on Peugeot 407 in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
All work should be done with the engine stopped.

Replacement: anti roll bar links – Peugeot 407 saloon. Use the following procedure:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts.Use wheel impact socket #19.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: anti roll bar links – Peugeot 407 saloon. Tip:

To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Clean the stabiliser link fasteners.Use a wire brush.Use WD-40 spray.

Step 7

Unscrew the fastener connecting the stabilizer link to the stabilizer bar.Use a combination spanner #18.Use HEX No.H6.Use a ratchet wrench.
Step 8

Unscrew the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #24.Use Torx T40.Use a ratchet wrench.
Step 9

Remove the fastening nut.

Step 10

Remove the stabilizer rod.Use a pin punch.Use a hammer.
Step 11

Clean the mounting seats of the stabiliser link.Use a wire brush.Use WD-40 spray.

Step 12

Install a new rod, tighten the fasteners.Use a crowbar.
Step 13

Tighten the fastener connecting the stabilizer link to the stabilizer bar.Use a combination spanner #18.Use HEX No.H6.Use a torque wrench.Tighten it to 65 Nm torque.
Step 14

Install the fastening nut.

Step 15

Tighten the fastener connecting the stabilizer bar with the control arm.Use a combination spanner #24.Use Torx T40.Use a torque wrench.Tighten it to 70 Nm torque.
Step 16

Treat all joints of the stabiliser link.Use copper grease.
Step 17

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 18

Clean the brake disk surface.Use a brake cleaner.

Replacement: anti roll bar links – Peugeot 407 saloon. Tip from AUTODOC:

After applying the spray, wait a few minutes.
Step 19

Install the wheel.

AUTODOC recommends:

Important! Hold the wheel while screwing in the fastening bolts. Peugeot 407 saloon
Step 20

Screw in the wheel bolts.Use wheel impact socket #19.
Step 21

Lower the car and working in a cross order, tighten the wheel bolts.Use wheel impact socket #19.Use a torque wrench.Tighten it to 120 nm torque.
Step 22

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

How to change rear brake pads on Peugeot 407 saloon – replacement guide

Free download PDF

7.56 MB
How to change rear wheel bearing on Peugeot 407 saloon – replacement guide

Free download PDF

14.26 MB
How to change front brake pads on Peugeot 407 saloon – replacement guide

Free download PDF

9.57 MB
How to change air filter on Peugeot 407 saloon – replacement guide

Free download PDF

8.26 MB
How to change track rod end on Peugeot 407 saloon – replacement guide

Free download PDF

7.69 MB
How to change rear anti roll bar links on Peugeot 407 saloon – replacement guide

Free download PDF

6.44 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.