Disclaimer
How to change front anti roll bar links on FIAT Bravo II Van (198) – replacement guide
downloads:
1
Views:
11
Important!
This replacement procedure can be used for:
FIAT Bravo II Van (198) 1.6 JTD Multijet (198AXH1B) … View more
The steps may slightly vary depending on the car design.
FIAT Bravo II Van (198) 1.6 JTD Multijet (198AXH1B) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for Bravo II Van (198) and other FIAT models
Anti-roll bar link
Alternative products
Anti-roll bar link
Wire brush
WD-40 spray
Copper grease
HEX bit No.H5
Combination spanner #17
Drive socket # 10
Drive socket # 17
Wheel impact socket #17
Ratchet wrench
Torque wrench
Phillips Screwdriver
Hydraulic transmission jack
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on FIAT Bravo II Kastenwagen (198) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- All work should be done with the engine stopped.
Replacement: anti roll bar links – FIAT Bravo II Kastenwagen (198). Recommended sequence of steps:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the front of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. FIAT Bravo II Kastenwagen (198) - Step 5
Remove the wheel. - Step 6
Chock the opposite wheel. Use a hydraulic transmission jack. - Step 7
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 8
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17. Use a ratchet wrench. - Step 9
Unscrew and remove the wheel arch cover fasteners. Use a drive socket #10. Use a ratchet wrench. Use a Phillips screwdriver. - Step 10
Remove the wheel arch cover. - Step 11
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 12
Unscrew the fasteners connecting the stabiliser link to the stabiliser bar. Use HEX No.H5. Use a combination spanner #17. Use a ratchet wrench. - Step 13
Remove the stabilizer rod.Replacement: anti roll bar links – FIAT Bravo II Kastenwagen (198). Professionals recommend:Examine stabiliser bushes. Replace them if needed. - Step 14
Install a new rod, tighten the fasteners.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the FIAT Bravo II Van (198) model
Popular maintenance tutorials for FIAT Bravo II Kastenwagen (198)
Free download PDF
3.04 MB
Free download PDF2.48 MB
Free download PDF1.61 MB
Free download PDF2.29 MB
Free download PDF2.17 MB
Free download PDF2.01 MB
Complete guides for changing the Drop links on different FIAT BRAVO models
Free download PDF1.77 MB
Free download PDF972.8 KB
Free download PDF1.37 MB
Free download PDF1.31 MB
Free download PDF1.28 MB
Free download PDF1.7 MB
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your FIAT Bravo II Van (198)
View more
Top 7 Manual Transmission Mistakes to Avoid | AUTODOC Tips
Discover the 4 Key Reasons Your CHECK ENGINE Light Could Be On | AUTODOC Tips
The Fast and Easy Way to Fix a Broken Wheel Stud | AUTODOC tips
How to remove rust | AUTODOC tips
Most commonly replaced car parts on FIAT BRAVO
Time to replace parts? Get even better deals in our Shop app.
SCAN ME