
Disclaimer
How to change front anti roll bar links on Citroën Berlingo M – replacement guide
downloads:
3
Views:
63
Important!
This replacement procedure can be used for:
CITROËN Berlingo / Berlingo First Van (M_) 1.1 i (MAHDZ, MBHDZ, MBHFX), CITROËN Berlingo / Berlingo First Van (M_) 1.4 i (MBKFX, MBKFW), CITROËN Berlingo / Berlingo First Van (M_) 1.8 D (MBA9A, MCA9A), CITROËN Berlingo / Berlingo First Van (M_) 1.9 D (MBDJY), CITROËN Berlingo / Berlingo First Van (M_) 1.9 D 70 (MBWJZ, MCWJZ), CITROËN Berlingo / Berlingo First Van (M_) 1.9 D 70 4WD (MBWJZ, MCWJZ), CITROËN Berlingo / Berlingo First Van (M_) 2.0 HDI, CITROËN Berlingo / Berlingo First Van (M_) 1.4 i bivalent (MBKFW), CITROËN Berlingo / Berlingo First Van (M_) 1.4 bivalent, CITROËN Berlingo / Berlingo First Van (M_) 1.8 i, CITROËN Berlingo / Berlingo First Van (M_) 2.0 HDI 4WD, CITROËN Berlingo / Berlingo First Van (M_) 1.6 16V (MBNFU), CITROËN Berlingo / Berlingo First Van (M_) 1.6 HDI, CITROËN Berlingo / Berlingo First Van (M_) Electric, CITROËN Berlingo / Berlingo First Van (M_) 1.6 HDI, CITROËN Berlingo / Berlingo First Van (M_) Electric, CITROËN Berlingo / Berlingo First Van (M_) 1.4 BiFuel (MBKFXB, MCKFXB) … View more
The steps may slightly vary depending on the car design.
CITROËN Berlingo / Berlingo First Van (M_) 1.1 i (MAHDZ, MBHDZ, MBHFX), CITROËN Berlingo / Berlingo First Van (M_) 1.4 i (MBKFX, MBKFW), CITROËN Berlingo / Berlingo First Van (M_) 1.8 D (MBA9A, MCA9A), CITROËN Berlingo / Berlingo First Van (M_) 1.9 D (MBDJY), CITROËN Berlingo / Berlingo First Van (M_) 1.9 D 70 (MBWJZ, MCWJZ), CITROËN Berlingo / Berlingo First Van (M_) 1.9 D 70 4WD (MBWJZ, MCWJZ), CITROËN Berlingo / Berlingo First Van (M_) 2.0 HDI, CITROËN Berlingo / Berlingo First Van (M_) 1.4 i bivalent (MBKFW), CITROËN Berlingo / Berlingo First Van (M_) 1.4 bivalent, CITROËN Berlingo / Berlingo First Van (M_) 1.8 i, CITROËN Berlingo / Berlingo First Van (M_) 2.0 HDI 4WD, CITROËN Berlingo / Berlingo First Van (M_) 1.6 16V (MBNFU), CITROËN Berlingo / Berlingo First Van (M_) 1.6 HDI, CITROËN Berlingo / Berlingo First Van (M_) Electric, CITROËN Berlingo / Berlingo First Van (M_) 1.6 HDI, CITROËN Berlingo / Berlingo First Van (M_) Electric, CITROËN Berlingo / Berlingo First Van (M_) 1.4 BiFuel (MBKFXB, MCKFXB) … View more
The steps may slightly vary depending on the car design.
How to change front anti roll bar link on CITROËN BERLINGO M [TUTORIAL AUTODOC]

All the parts you need to replace – Anti Roll Bar Links for Berlingo / Berlingo First Van (M_) and other CITROËN models
Anti-roll bar link
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Ceramic grease
Copper grease
Torque wrench
Combination spanner #17
Drive socket # 17
HEX No.H6 bit socket
Wheel impact socket #19
Ratchet wrench
Wheel chock
Replacement: anti roll bar links – Citroën Berlingo M. Tip from AUTODOC:
- Replace the stabiliser links on Citroën Berlingo M in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – Citroën Berlingo M – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2Loosen the wheel mounting bolts. Use wheel impact socket #19.
- Step 3Raise the car.Replacement: anti roll bar links – Citroën Berlingo M. AUTODOC experts recommend:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
- Step 4Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Citroën Berlingo M
- Step 5Remove the wheel.
- Step 6Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
- Step 7Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17. Use a ratchet wrench.
- Step 8Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use HEX No.H6. Use a ratchet wrench.
- Step 9Remove the stabiliser link.Replacement: anti roll bar links – Citroën Berlingo M. Professionals recommend:Examine stabiliser bushes. Replace them if needed.
- Step 10Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
- Step 11Treat the thread of the sway bar link fasteners. Use copper grease.
- Step 12Install a new stabiliser link and tighten the fasteners. Use a drive socket #17. Use a ratchet wrench.
- Step 13Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #17. Use a torque wrench. Tighten it to 40 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the CITROËN Berlingo / Berlingo First I Van (M) model
Popular maintenance tutorials for Citroën Berlingo M
Complete guides for changing the Drop links on different CITROËN BERLINGO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your CITROËN Berlingo / Berlingo First Van (M_)
View more
- Top 7 Manual Transmission Mistakes to Avoid | AUTODOC Tips
- Why Is the Windscreen Washer Not Spraying? Solution
- 5 tools that make car repair incredibly simple | AUTODOC tips
- Drive with Care: 8 Common Bad Driving Habits Explained | AUTODOC
Most commonly replaced car parts on CITROËN BERLINGO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME