Disclaimer
How to change front anti roll bar links on CITROËN Berlingo II Van (B9) – replacement guide
downloads:
5
Views:
124
Important!
This replacement procedure can be used for:
CITROËN BERLINGO Box (B9) 1.6 HDi 16V … View more
The steps may slightly vary depending on the car design.
CITROËN BERLINGO Box (B9) 1.6 HDi 16V … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for BERLINGO Box (B9) and other CITROËN models
Anti-roll bar link
Rod / Strut, wheel suspension
Repair Kit, stabilizer suspension
Repair Kit, stabilizer coupling rod
Mounting, stabilizer coupling rod
Torsion Bar Linkage
Wire brush
WD-40 spray
Brake cleaner
Ceramic grease
Copper grease
Torque wrench
Combination spanner #17
Drive socket # 17
HEX No.H6 bit socket
Wheel impact socket #19
Ratchet wrench
Wheel chock
Replacement: anti roll bar links – CITROËN BERLINGO Box (B9). Tip from AUTODOC:
- Replace the stabiliser links on CITROËN BERLINGO Box (B9) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – CITROËN BERLINGO Box (B9) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3Raise the car.AUTODOC recommends:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. CITROËN BERLINGO Box (B9) - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17. Use a ratchet wrench. - Step 8
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use HEX No.H6. Use a ratchet wrench. - Step 9
Remove the stabiliser link.Replacement: anti roll bar links – CITROËN BERLINGO Box (B9). Professionals recommend:Examine stabiliser bushes. Replace them if needed. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Treat the thread of the sway bar link fasteners. Use copper grease. - Step 12
Install a new stabiliser link and tighten the fasteners. Use a drive socket #17. Use a ratchet wrench. - Step 13
Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #17. Use a torque wrench. Tighten it to 40 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the CITROËN Berlingo II Van (B9) model
Popular maintenance tutorials for Citroen Berlingo mk2
Free download PDF
1.52 MB
Free download PDF1.93 MB
Free download PDF5.01 MB
Free download PDF2.46 MB
Free download PDF1.09 MB
Free download PDF1.46 MB
Complete guides for changing the Drop links on different CITROËN BERLINGO models
Free download PDF1.14 MB
Free download PDF2.08 MB- Free download PDF1.09 MB
Free download PDF1.34 MB
Free download PDF1.34 MB
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your CITROËN BERLINGO Box (B9)
View more
Discover the 4 Key Reasons Your CHECK ENGINE Light Could Be On | AUTODOC Tips
TOP 8 mistakes car owners make | AUTODOC tips
Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips
K2 ROTON wheel cleaner overview
Most commonly replaced car parts on CITROËN BERLINGO
Time to replace parts? Get even better deals in our Shop app.
SCAN ME