Important!

This replacement procedure can be used for:
CITROËN Berlingo Van (K9) 1.6 BlueHDi, CITROËN Berlingo Van (K9) 1.6 BlueHDi, CITROËN Berlingo Van (K9) 1.5 BlueHDi, CITROËN Berlingo Van (K9) 1.5 BlueHDi, CITROËN Berlingo Van (K9) PureTech … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – CITROËN BERLINGO (K9). Tools you need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Combination spanner #16
                    
                      Drive socket # 15 
                    
                      Drive socket # 17 
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Wheel chock

Buy tools

Replacement: anti roll bar links – CITROËN BERLINGO (K9). AUTODOC experts recommend:

Replace the stabiliser links on CITROËN BERLINGO (K9) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
All work should be done with the engine stopped.

Replacement: anti roll bar links – CITROËN BERLINGO (K9). Recommended sequence of steps:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: anti roll bar links – CITROËN BERLINGO (K9). AUTODOC recommends:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Remove the ABS wiring harness bracket.
Step 7

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 8

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #15. Use a ratchet wrench.
Step 9

Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 10

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use a drive socket #15. Use a ratchet wrench.
Step 11

Remove the stabilizer rod.

Replacement: anti roll bar links – CITROËN BERLINGO (K9). Tip from AUTODOC experts:
Examine stabiliser bushes. Replace them if needed.
Step 12

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 13

Install a new rod, tighten the fasteners.
Step 14

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a drive socket #17. Use a torque wrench. Tighten it to 36 Nm torque.
Step 15

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #17. Use a torque wrench. Tighten it to 36 Nm torque.
Step 16

Treat all joints of the stabiliser link. Use copper grease.
Step 17

Install the ABS wiring harness bracket.
Step 18

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 19

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – CITROËN BERLINGO (K9). After applying the spray, wait a few minutes.
Step 20

Install the wheel.

Replacement: anti roll bar links – CITROËN BERLINGO (K9). Tip from AUTODOC:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 21

Screw in the wheel bolts. Use wheel impact socket #17.
Step 22

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 100 nm torque.
Step 23

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the CITROËN Berlingo Van (K9) model

CITROËN BERLINGO (K9) tyre size

How to change front windshield wipers on CITROËN Berlingo Van (K9) – replacement guide

Free download PDF
706.56 KB
How to change engine oil and filter on CITROËN Berlingo Van (K9) – replacement guide

Free download PDF
1.17 MB
How to change fuel filter on CITROËN Berlingo Van (K9) – replacement guide

Free download PDF
931.84 KB
How to change serpentine belt on Citroen Xsara Picasso – replacement guide

Free download PDF
1.72 MB
How to change serpentine belt on Citroen C3 1 – replacement guide

Free download PDF
1.02 MB
How to change rear brake shoes on Citroën Berlingo M – replacement guide

Free download PDF
2.56 MB

How to change front anti roll bar links on Citroën Berlingo M – replacement guide

Free download PDF
1.14 MB
How to change front anti roll bar links on CITROËN Berlingo II (B9) – replacement guide

Free download PDF
2.08 MB
How to change front anti roll bar links on CITROËN Berlingo II Van (B9) – replacement guide

Free download PDF
1.98 MB
How to change front anti roll bar links on CITROËN BERLINGO Box (B9) – replacement guide

Free download PDF
1.09 MB
How to change front anti roll bar links on CITROËN Berlingo / Berlingo First I (MF, GJK, GFK) – replacement guide

Free download PDF
2.14 MB
How to change front anti roll bar links on CITROËN Berlingo (K9) – replacement guide

Free download PDF
1.34 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips

8K views

Published on: 16/12/2021
DIY vehicle AC compressor restoration

745K views

Published on: 28/11/2024
5 causes of turbocharger failure and how to avoid them

15K views

Published on: 04/04/2024
Fuse Replacement Made Simple: Step-by-Step Guide | AUTODOC

3K views

Published on: 15/08/2020