Replace the brake disks on the car Honda CR-V II in complete set for each axis. Regardless of the state of components. This will ensure even braking.
The replacement procedure is identical for both brake disks on the same axle.
When changing the brake discs, always replace the brake pads.
Please note: all work on the car – Honda CR-V II – should be done with the engine switched off.
Carry out replacement in the following order:
Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2
Secure the wheels with chocks.
Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 4
Raise the front of the car and secure on supports.
Step 5
Unscrew the wheel bolts.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Honda CR-V II
Step 6
Remove the wheel.
Step 7
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 8
Unscrew the brake caliper fastening. Use a drive socket #12. Use a ratchet wrench.
Step 9
Spread the brake pads. Use a crowbar.
Step 10
Remove the brake caliper.
Replacement: brake discs – Honda CR-V II. Tip:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 11
Remove the retaining springs of the brake pads.
Step 12
Remove the brake pads. Use a crowbar.
Step 13
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 14
Unscrew the caliper bracket fastening. Use a drive socket #17. Use a ratchet wrench.
Step 15
Remove the caliper bracket.
Step 16
Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
Step 17
Unscrew the brake disc fastening. Use an impact screwdriver. Use a hammer.
Step 18
Remove the brake disc.
Step 19
Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 20
Install the brake disc.
Step 21
Tighten the brake disc fastening. Use a Phillips screwdriver. Use a torque wrench. Tighten it to 9 Nm torque.
Step 22
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake discs – Honda CR-V II. After applying the spray, wait a few minutes.
Step 23
Install the brake caliper bracket.
Step 24
Tighten the brake caliper bracket. Use a drive socket #17. Use a torque wrench. Tighten it to 108 Nm torque.
Step 25
Install the brake pads.
Step 26
Install the retaining springs of the brake pads.
Step 27
Treat the brake caliper piston. Use a brake cleaner.
Replacement: brake discs – Honda CR-V II. Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 28
Press in the brake caliper piston. Use brake caliper wind back tool.
Step 29.1
Install the brake caliper and fix it.
Step 29.2
Use a drive socket #12. Use a torque wrench. Tighten it to 34 Nm torque.
Step 30
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 31
Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake discs – Honda CR-V II. After applying the spray, wait a few minutes.
Step 32
Install the wheel.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. Honda CR-V II
Step 33
Screw in the wheel bolts. Use wheel impact socket #19.
Step 34
Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 108 Nm torque.
Step 35
Remove the jacks and chocks.
Replacement: brake discs – Honda CR-V II. AUTODOC experts recommend:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 36
Tighten the brake fluid reservoir cap. Close the hood.
Replacement: brake discs – Honda CR-V II. Tip from AUTODOC experts:
Without starting the engine, press the brake pedal several times until you feel significant resistance.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the HONDA CR-V II (RD) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your HONDA CR-V II (RD_)
View more
How to restore wheel rims | AUTODOC tips
Things you should never do with your manual transmission | AUTODOC tips