When to replace the Poly V-Belt on your PEUGEOT PARTNER
Recommended replacement interval for the part category Serpentine belt : 2 year / 15000 km
Important!
This replacement procedure can be used for:
PEUGEOT PARTNER Box (5) 1.9 D, PEUGEOT PARTNER Box (5) 1.9 D View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Poly V-Belt for PARTNER Box (5) and other PEUGEOT models
Tools
Replacement: serpentine belt – PEUGEOT PARTNER Box (5). List of the tools you'll need:
Wire brush
Torque wrench
Drive socket # 27
HEX bit no.H8
1/4" square drive extension bar
Wheel impact socket #19
Ratchet wrench
Clip removal tool
Phillips screwdriver
Fender cover
Wheel chock
Replacement: serpentine belt – PEUGEOT PARTNER Box (5). Tools you might need:
  • All work should be done with the engine stopped.
Replacement: serpentine belt – PEUGEOT PARTNER Box (5). Use the following procedure:
  1. Step 1
    Open the hood.
    Step 2
    Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
    Step 3
    Secure the wheels with chocks.
    Step 4
    How to change Poly V-Belt on Peugeot Partner Van 1996 - free PDF and video manuals
    Loosen the wheel mounting bolts. Use wheel impact socket #19.
  2. Step 5
    Raise the car.
    Replacement: serpentine belt – PEUGEOT PARTNER Box (5). AUTODOC recommends:
    If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
    Step 6
    How to replace PEUGEOT PARTNER Box (5) 1.9 D 1997 Poly V-Belt - step-by-step manuals and video guides
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. PEUGEOT PARTNER Box (5)
  3. Step 7
    Peugeot Partner Van 2.0 HDi 1998 Poly V-Belt replacement: free workshop manuals
    Remove the wheel.
  4. Step 8
    Changing Poly V-Belt on PEUGEOT PARTNER Box (5) 1.6 HDi 75 1999 by yourself
    Unscrew and remove the wheel arch cover fasteners. Use a clip removal tool. Use a Phillips screwdriver.
  5. Step 9
    How to remove PEUGEOT PARTNER 1.4 2000 Poly V-Belt - online easy-to-follow instructions
    Remove the wheel arch cover.
  6. Step 10
    How to replace Poly V-Belt on PEUGEOT PARTNER Box (5) 2001: download PDF manuals and video instructions
    Release the coolant pipe fasteners.
  7. Step 11
    How hard is it to do yourself: Poly V-Belt replacement on Peugeot Partner Van 1.1 2002 - download illustrated guide
    Clean the tensioner pulley fastener. Use a wire brush.
  8. Step 12
    Need to know how to renew Poly V-Belt on PEUGEOT PARTNER 2003? This free workshop manual will help you to do it yourself
    Loosen the tensioner pulley fastener. Use HEX No.H8. Use a ratchet wrench.
  9. Step 13
    Changing of Poly V-Belt on Peugeot Partner Van 2004 won't be an issue if you follow this illustrated step-by-step guide
    Pull aside the V-ribbed belt tensioner pulley. Use a 1/4" square drive extension bar. Use a ratchet wrench.
  10. Step 14
    PEUGEOT PARTNER 1.9 D Poly V-Belt replacement: online guides and video tutorials
    Remove the V-ribbed belt.
    Replacement: serpentine belt – PEUGEOT PARTNER Box (5). Tip from AUTODOC experts:
    Check the condition of the tensioner pulley and idler pulley. Replace them if necessary.
  11. Step 15
    Replacing Poly V-Belt on Peugeot Partner Van 2006 1.9 D by yourself
    Install the V-ribbed belt.
    Replacement: serpentine belt – PEUGEOT PARTNER Box (5). Professionals recommend:
    Make sure that the V-ribbed belt fits all pulleys snugly.
  12. Step 16
    PARTNER Box (5) 1.4 2007 Poly V-Belt DIY replacement workshop manual
    Tension the belt by turning the tensioner pulley clockwise. Use a 1/4" square drive extension bar. Use a ratchet wrench.
    Replacement: serpentine belt – PEUGEOT PARTNER Box (5). Tip:
    Keep the belt taut until you've tightened the tensioner pulley fastener.
  13. Step 17
    How to change Poly V-Belt on PEUGEOT PARTNER Box (5) 2008 - tips and tricks
    Tighten the fastener of the serpentine belt tensioner pulley. Use HEX No.H8. Use a torque wrench. Tighten it to 35 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT Partner I Van model.

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
PEUGEOT PARTNER Box (5) Poly V-Belt replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY PEUGEOT PARTNER Box (5) Poly V-Belt replacement - online guide
Tips & tricks for your PEUGEOT PARTNER Box (5)
View more
  • How to change Alternator belt on PEUGEOT PARTNER Box (5) 1.6 HDi 90 - replacement tricks
    How to replace the suspension on a BMW E30 Turbo | SUPERCAR AUTODOC
  • Changing Auxiliary belt Peugeot Partner Van 1.9 D - Replacement Tips
    Things you should never do with your manual transmission | AUTODOC tips
  • Maintenance Hacks - PEUGEOT PARTNER Box (5) 2.0 HDi Poly V-belt replacement guide
    What to do if your car heater isn't working | AUTODOC tips
  • Replace Drive belt on Peugeot Partner Van - free video tips
    How to polish an old engine valve cover to a shiny finish | AUTODOC Tips